CY7C1347C/GVT71128DA36
CY7C1327C/GVT71256DA18
256K x 18/128K x 36 Synchronous-Pipelined
Cache RAM
The CY7C1347C/GVT71128DA36 and CYC7C1327C/
GVT71256DA18 SRAMs integrate 131,072x36 and
262,144x18 SRAM cells with advanced synchronous periph-
Features
• Fast access times: 2.5 and 3.5 ns
eral circuitry and a 2-bit counter for internal burst operation. All
synchronous inputs are gated by registers controlled by a pos-
itive-edge-triggered clock input (CLK). The synchronous in-
puts include all addresses, all data inputs, address-pipelining
Chip Enable (CE), depth-expansion Chip Enables (CE2 and
CE2), Burst Control Inputs (ADSC, ADSP, and ADV), Write
Enables (BWa, BWb, BWc, BWd, and BWE), and Global Write
(GW).
• Fast clock speed: 250, 225, 200, and 166 MHz
• 1-ns set-up time and hold time
• Fast OE access times: 2.5 ns and 3.5 ns
• Optimal for depth expansion (one cycle chip deselect
to eliminate bus contention)
• 3.3V –5% and +10% power supply
• 3.3V or 2.5V I/O supply
• 5V tolerant inputs except I/Os
Asynchronous inputs include the Output Enable (OE) and
Burst Mode Control (MODE). The data outputs (Q), enabled
by OE, are also asynchronous.
• Clamp diodes to V at all inputs and outputs
SS
• Common data inputs and data outputs
Addresses and chip enables are registered with either Ad-
dress Status Processor (ADSP) or Address Status Controller
(ADSC) input pins. Subsequent burst addresses can be inter-
nally generated as controlled by the Burst Advance pin (ADV).
• Byte Write Enable and Global Write control
• Three chip enables for depth expansion and address
pipeline
• Address, data, and control registers
• Internally self-timed Write Cycle
• Burst control pins (interleaved or linear burst se-
quence)
• Automatic power-down for portable applications
• JTAG boundary scan
• JEDEC standard pinout
• Low profile 119-lead, 14-mm x 22-mm BGA (Ball Grid
Array) and 100-pin TQFP packages
Address, data inputs, and write controls are registered on-chip
to initiate self-timed Write cycle. Write cycles can be one to
four bytes wide as controlled by the write control inputs. Indi-
vidual byte write allows individual byte to be written. BWa con-
trols DQa. BWb controls DQb. BWc controls DQc. BWd con-
trols DQd. BWa, BWb, BWc, and BWd can be active only with
BWE being LOW. GW being LOW causes all bytes to be writ-
ten. The x18 version only has 18 data inputs/outputs (DQa and
DQb) along with BWa and BWb (no BWc, BWd, DQc, and
DQd).
Functional Description
Four pins are used to implement JTAG test capabilities: Test
Mode Select (TMS), Test Data-in (TDI), Test Clock (TCK), and
Test Data-out (TDO). The JTAG circuitry is used to serially shift
data to and from the device. JTAG inputs use LVTTL/LVCMOS
levels to shift data during this testing mode of operation.
The Cypress Synchronous Burst SRAM family employs
high-speed, low-power CMOS designs using advanced tri-
ple-layer polysilicon, double-layer metal technology. Each
memory cell consists of four transistors and two high-valued
resistors.
The
CY7C1347C/GVT71128DA36
and
CY7C1327C/
GVT71256DA18 operate from a +3.3V power supply. All inputs
and outputs are LVTTL compatible
Selection Guide
7C1347C-250
7C1347C-225
71128DA36-4.4
7C1327C-225
71256DA18-4.4
7C1347C-200
71128DA36-5
7C1327C-200
71256DA18-5
7C1347C-166
71128DA36-6
7C1327C-166
71256DA18-6
71128DA36-4
7C1327C-250
71256DA18-4
Maximum Access Time (ns)
2.5
450
10
2.5
400
10
2.5
360
10
3.5
300
10
Maximum Operating Current (mA)
Maximum CMOS Standby Current (mA)
Cypress Semiconductor Corporation
•
3901 North First Street
•
San Jose
•
CA 95134
•
408-943-2600
July 21, 2000
5秒后页面跳转
STM32H743技术深度剖析与应用案例探索
LM321中文资料解析：引脚功能介绍、技术特点、技术特性分析
74HC14芯片资料介绍：性能特性分析、引脚介绍
LM1875芯片手册：功放参数分析、引脚说明、电路设计要点
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
