GPJ8A~GPJ8M
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
Unit: inch (mm)
GPJ
CURRENT
8.0 Ampere
VOLTAGE
50 to 1000 Volts
FEATURES
• Plastic material has Underwriters Laboratory, Flammability Classification 94V-O
• Ideal for printed circuit board
1.192(30.3)
1.169(29.7)
.208(5.3)
.189(4.8)
• Reliable low cost construction utilizing molded plastic technique
• High temperature soldering guaranteed:
.171(4.35)
.159(4.05)
260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
• Pb free product are available : 99% Sn above can meet RoHS environment
substance diective request
MECHANICALDATA
.133(3.4)
.125(3.2)
.087(2.2)
.070(1.8)
• Case: Reliable low cost construction utilizing
• molded plastic technique
.044(1.1)
.035(0.9)
• Terminals: Leads solderable per MIL-STD-750,Method 2026
• Mounting position: Any
.032(0.8)
.024(0.6)
.401(10.2)
.385(9.8)
.304(7.7)
.288(7.3)
.304(7.7)
.288(7.3)
• Mounting torque: 5 in. lb. Max.
• Weight: 0.15 ounce, 4.0 grams
MAXIMUMRATINGSANDELECTRICALCHARACTERISTICS
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
PARAMETER
SYMBOL GPJ8A GPJ8B GPJ8D GPJ8G GPJ8J GPJ8K GPJ8M UNITS
Maximum Recurrent Peak Reverse Voltage
50
35
50
100
70
200
140
200
400
280
400
600
420
600
800
560
800
1000
700
V
V
VRRM
VRMS
VDC
IF(AV)
I2 t
Maximum RMS Bridge Input Voltage
Maximum DC Blocking Voltage
100
1000
V
Maximum Average Forward TC=100 OC
Rectified Output Current at TA=40 OC
8.0
6.0
A
I2 t Rating for fusing ( t<8.3ms)
166
200
1.1
A2 sec
Apk
Vpk
uA
Peak Forward Surge Current single sine-wave superimposed
on rated load (JEDEC method)
IFSM
VF
Maximum Instantaneous Forward Voltage Drop per element
at 4.0A
Maximum Reverse Leakage Current at Rated @ TJ=25O
Dc Blocking Voltage @ TJ=100O
C
10
500
IR
C
Typical Thermal Resistance per leg (Note 2)
(Note 3)
RθJA
RθJC
8.6
3.1
O C/W
Operating Junction and Storage Temperature Range
-55 to + 150
TJ,TSTG
O C
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.
STAD-MAY.23.2006
PAGE . 1