Approve Sheet P a r t N u mb e r : G B J 6 A~G B J 6 K
DATA SHEET
GBJ 6 A~ GBJ 6 K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE - 50 to 800 Volts CURRENT - 6.0 Amperes
Unit: inch ( mm )
GBJ
FEATURES
• Plastic material has Underwriters Laboratory
Flammability Classification 94V-O
(
0.189 4.8
)
0.996(25.3)
0.972(24.7)
(
0.173 4.4
)
• Ideal for printed circuit board
(
)
0.150 3.8
• Reliable low cost construction utilizing molded plastic technique
• Surge overload rating: 175 Amperes peak
(
0.133 3.4
)
• High temperature soldering guaranteed:
260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
MECHANICAL DATA
Case: Reliable low cost construction utilizing
0.115(2.9)
0.098(2.5)
(
0.087 2.2
(
0.070 1.8
)
)
molded plastic technique
Terminals: Leads solderable per MIL-STD-202,
Method 208
(
0.044 1.1
)
0.035(0.9)
(
0.032 0.8
)
Mounting position: Any
(
0.024 0.6
)
0.304(7.7)
0.288(7.3)
0.304(7.7)
0.288(7.3)
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams
0.304(7.7)
0.288(7.3)
MAXIMUMRATINGSANDELECTRICALCHARACTERISTICS
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
UNIT
V
GBJ6A
50
GBJ6B
100
GBJ6D
200
GBJ6G
GBJ6J
GBJ6K
800
400
280
400
600
420
600
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Input Voltage
35
50
70
140
200
560
800
V
V
100
Maximum DC Blocking Voltage
Maximum Average Forward TC=100°C
Rectified Output Current
6.0
A
I2t Rating for fusing ( t<8.3ms)
A2sec
127
Peak Forward Surge Current single sine-wave superimposed on rated load
(JEDEC method)
175
1.0
Apk
Vpk
Maximum Instantaneous Forward Voltage Drop per element at 6.0A
µA
µA
Maximum Reverse Leakage at rated TA=25°
CDc Blocking Voltage per element TC=100°C
5
500
°C / W
°C / W
°C
Typical Thermal Resistance per leg(Note 2) RθJA
Typical Thermal Resistance per leg(Note 3) RθJC
Operating and Storage Temperature Range, TJ,TSTG
8.6
3.1
-55 to +150
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.
P AGE . 1