DATA SHEET
GBJ6A~GBJ6K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
CURRENT
6.0 Ampere
Unit: inch (mm)
GBJ
VOLTAGE
50 to 800 Volts
Recongnized File #E228882
FEATURES
.996(25.3)
.972(24.7)
.189(4.8)
.173(4.4)
• Plastic material has Underwriters Laboratory
Flammability Classification 94V-O
.150(3.8)
.133(3.4)
• Ideal for printed circuit board
• Reliable low cost construction utilizing molded plastic technique
• High temperature soldering guaranteed:
260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
• Both normal and Pb free product are available:
Normal : 80~95% Sn, 5~20% Pb
Pb free: 98.5% Sn above
.115(2.9)
.098(2.5)
.087(2.2)
.070(1.8)
MECHANICALDATA
.044(1.1)
.035(0.9)
Case: Reliable low cost construction utilizing
molded plastic technique
.032(0.8)
.024(0.6)
.304(7.7)
.288(7.3)
.304(7.7)
.288(7.3)
Terminals: Leads solderable per MIL-STD-202,
Method 208
.304(7.7)
.288(7.3)
Mounting position: Any
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams
MAXIMUMRATINGSANDELECTRICALCHARACTERISTICS
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
PARAMETER
SYMBOL GBJ6A GBJ6B GBJ6D GBJ6G GBJ6J GBJ6K UNITS
Maximum Recurrent Peak Reverse Voltage
50
35
50
100
70
200
140
200
400
280
400
600
420
600
800
560
800
V
V
V
V
RRM
RMS
Maximum RMS Bridge Input Voltage
Maximum DC Blocking Voltage
100
V
V
DC
Maximum Average Forward Rectified Output Current at
6.0
127
175
1.0
A
I
AV
TC
=100 OC
I2t Rating for fusing ( t<8.3ms)
A2sec
Apk
Vpk
uA
I2t
Peak Forward Surge Current single sine-wave superimposed
on rated load (JEDEC method)
I
FSM
Maximum Instantaneous Forward Voltage Drop per element at
3.0A
V
F
Maximum Reverse Leakage Current at Rated @ T
Dc Blocking Voltage @ T
=100OC
A
=25OC
5.0
500
I
R
A
Typical Thermal Resistance per leg (Note 2)
(Note 3)
RθJA
RθJC
8.6
3.1
OC/W
Operating Junction and Storage Temperature Range
-55 to + 150
TJ,TSTG
OC
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.
STAD-FEB.20.2004
PAGE . 1