G674/G675
Global Mixed-mode Technology
Microprocessor Reset IC
Features
General Description
Precision Monitoring of +2.5V and +3V
The G674/G675 are microprocessor (µP) supervisory
circuits used to monitor the power supplies in µP and
digital systems. They provide excellent circuit reliability
and low cost and adjustments when used with +2.5V,
+3.0V powered circuits.
Power-Supply Voltages
Fully Specified Over Temperature
Available in Three Output Configurations
Push-Pull RESET Output (G674L)
Push-Pull RESET Output (G674H)
These circuits perform a single function: they assert a reset
signal whenever the VCC supply voltage declines below a
preset threshold, with hysteresis keeping it asserted for
time delay determined by externally programmable time
delay generator after VCC has risen above the reset thresh-
old. Reset thresholds suitable for operation with a variety of
supply voltages are available.
Open-Drain RESET Output (G675L)
Externally Programmable Time Delay Generator
14µA Supply Current
Guaranteed Reset Valid to VCC = 0.8V
Power Supply Transient Immunity
5 pin SOT-23-5 and 6 pin TDFN2X2 Packages
2% Threshold Accuracy
The G675L has an open-drain output stage, while the
G674 have push-pull outputs. The G675L’s open-drain
Applications
RESET output requires a pull-up resistor that can be
connected to a voltage higher than VCC. The G674L have
Computers
Controllers
an active-low RESET output, while the G674H has an
active-high RESET output. The reset comparator is de-
signed to ignore fast transients on VCC, and the outputs
are guaranteed to be in the correct logic state for VCC
down to 0.8V.
Intelligent Instruments
Critical µP and µC Power Monitoring
Portable / Battery-Powered Equipment
Automotive
Low supply current makes the G674/G675 ideal for use in
portable equipment. The G674/G675 are available in
5-pin SOT-23-5 and 6 pin TDFN2X2 packages.
Ordering Information
ORDER
NUMBER
TEMP.
RANGE
PACKAGE
(Green)
G674HxxxT1U
G674LxxxT1U
G675LxxxT1U
G674HxxxRB1U
G674LxxxRB1U
G675LxxxRB1U
-40°C ~ +105°C
-40°C ~ +105°C
-40°C ~ +105°C
-40°C ~ +105°C
-40°C ~ +105°C
-40°C ~ +105°C
SOT-23-5
SOT-23-5
SOT-23-5
TDFN2X2-6
TDFN2X2-6
TDFN2X2-6
* xxx specifies the threshold voltage.
e.g. 240 denotes the 2.4V threshold voltage.
Pin Configuration
Typical Application Circuit
VCC
G674/G675
VCC
VCC
Rpull-up*
CD
RESET(RESET)
1
5
4
GND
RESET(RESET)
VCC
1
2
3
6
5
4
CD
G674/G675
Thermal
Pad
µP
N.C.
N.C.
VCC
GND
G674/G675
SOT-23-5
2
3
RESET
RESET
(RESET)
CD
INPUT
N.C.
GND
GND
TDFN2X2-6
CD
Note: Recommend connecting the Thermal Pad
to the Ground for excellent power dissipation.
()is for G674H
*G675 ONLY
ICC may increased at high TA, Therefore, can not connect
Resistors to VCC to prevent Icc abnormal behavior at high TA.
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.3
Apr 10, 2012
1