FIAM™
Actual size:
2.28 x 2.2 x 0.5 in
57,9 x 55,9 x 12,7 mm
Filter Input Attenuator Module
FIAM is housed in an industry standard "half brick"
module measuring 2.28" x 2.2" x 0.5" and
depending upon model selected, may be mounted
on-board or in-board for height critical applications.
Features
• RoHS Compliant (with F or G pin style)
• EMI filtering-Class B(1)
• Transient protection
• Low profile mounting options
• 10 and 20 Ampere versions
• UL, CSA, EN compliance
• Mini-size package
Compatible Products
•
Mini, Micro, Maxi 48 V Input DC-DC converters
• Inrush current limiting
Product Highlights
Absolute Maximum Rating
The FIAM is a DC front-end module providing
transient protection, inrush current limiting and
Class B EMI filtering in a Mini-size package. The
FIAM enables designers using Vicor 48 Vin Mini,
Micro, or Maxi DC-DC converters to meet the
transient immunity and EMI requirements of
Bellcore, FCC, ETSI and European Norms and
protect system hardware from inrush current. The
FIAM accepts an input voltage of 36 – 76 Vdc, is
available in 10 or 20 A versions and provides
reverse polarity protection and remote on/off control.
Parameter
Rating
80
Unit
Vdc
V
Notes
Continuous
+In to –In
100
100 ms
+Out to –Out
75
Vdc
in-lbs
°C
Continuous
Mounting torque
5(0.57)
6 each, #4-40 or M3
T and H -Grade
H-Grade
Operating temperature
Storage temperature
– 40 to +100
– 55 to +125
500 (260)
°C
°F(°C)
°F(°C)
<5 sec; wave solder
<7 sec; hand solder
Pin soldering temperature
750 (390)
Internally, the FIAM employs a transient suppressor
diode directly across the input. Refer to Figure 1.
This is followed by a passive EMI filter that
provides attenuation of both common mode and
differential mode conducted emissions. Surge
protection and inrush current limiting is
Thermal Resistance
Parameter
Min
Typ
Max
Unit
Baseplate to sink
flat, greased surface
0.16
0.14
°C/Watt
°C/Watt
accomplished by a MOS FET in series with the
positive rail whose gate is driven by the charge
pump/control circuit. During normal operation the
FET is fully enhanced; essentially a closed switch.
The charge pump limits the time rate of change of
gate bias voltage at startup, or in the event of a
voltage surge at the input. During this condition, the
source terminal of the FET follows the gate, offset by
the gate threshold voltage. A transient event at the
input, or drain terminal of the FET is therefore
attenuated and absorbed by the FET, which during
this condition is in the source follower mode. As a
result, the transient is virtually non existent at the
output of the FIAM. In addition, upon application of
power, the controlled voltage ramp up, limits the
rate at which the output capacitor is charged, thereby
limiting inrush current.
thermal pad (P/N 20264)
Baseplate to ambient
Free Convection
8.0
1.9
°C/Watt
°C/Watt
1000 LFM
Part Numbering
FIAM 1
C
1
1
Baseplate
1 = Slotted
2 = Threaded
3 = Thru-hole
Pin Style
Product Grade Temperatures (°C)
Type
Product
1 = Short
2 = Long
S = Short ModuMate
N = Long ModuMate
F = Short RoHS
G = Long RoHS
K = Extra Long RoHS
Grade
Operating
Storage
1 = 10 A
2 = 20 A
E
C
T
=
=
=
=
–10 to +100 –20 to 125
–20 to +100 –40 to 125
–40 to +100 –40 to 125
–40 to +100 –55 to 125
H
[1]
[1]
Not intended for socket or Surfmate mounting
™
FIAM
Rev 2.1
vicorpower.com
800 927.9474
Page 1 of 6
12/2014