APPLICABLE STANDARD
Operating
Storage temperature
range
-55 C to 125 C (note 1)
50V AC / DC
-10 C TO 50C(Packed condition)
Relative humidity 90%MAX(Not dewed)
t=0.30±0.05mm, Gold plating
temperature range
Operating or storage
humidity range
Applicable cable
(FPC/FFC)
RATING Voltage
Current
0.50 A
SPECIFICATIONS
TEST METHOD
ITEM
REQUIREMENTS
QT AT
CONSTRUCTION
General examination
Visually and by measuring instrument.
Confirmed visually.
According to drawing.
×
×
×
×
Marking
ELECTRICAL CHARACTERISTICS
Voltage proof
150 V AC for 1 min.
No flashover or breakdown.
×
×
-
-
Insulation resistance
100 V DC.
500 M MIN.
Contact resistance
AC 20 mV MAX , 1 mA .
Initial:50 m MAX、After each test:70 m
MAX (Including FPC/FFC bulk resistance
L=8mm)
×
-
MECHANICAL CHARACTERISTICS
Vibration
Frequency 10 to 55 Hz, half amplitude
① No electrical discontinuity of 1 s.
② Contact resistance: 70 m MAX
③ No damage, crack and looseness of parts.
×
×
×
×
-
-
-
-
0.75 mm, for 10 cycles in 3 axial directions.
981 m/s2 , duration of pulse 6 ms
at 3 times in 3 both axial directions.
10 times insertions and extractions.
Shock
Mechanical operation
① Contact resistance: 70 m MAX
② No damage, crack and looseness of parts.
Direction of extraction
FPC/FFC
retention force
Measured by applicable FPC/FFC.
(Thickness of FPC/FFC shall be t=0.30mm
at initial condition.)
20.5 N MIN (note2)
ENVIRONMENTAL CHARACTERISTICS
Rapid change of
temperature
Temperature-55→+15TO+35→+125→+15TO+35C
Time 30→ 2 to 3 → 30 → 2 to 3 min
① Contact resistance: 70 m MAX
② Insulation resistance: 50 M MIN.
③ No damage, crack and looseness of parts.
×
-
Under 1000 cycles.
Damp heat (Steady state)
Damp heat,cyclic
Exposed at 60±2 C,
Relative humidity 90 to 95 %, 1000 h.
×
×
-
-
Exposed at -10 to +65 c,
Relative humidity 90 to 96 %,
10 cycles, TOTAL 240 h.
① Contact resistance: 70 m MAX
② Insulation resistance: 1 M MIN.
(At high humidity)
③ Insulation resistance: 50 M MIN. (At dry)
④ No damage, crack and looseness of parts
① Contact resistance: 70 m MAX
Dry heat
Cold
Exposed at 125±2℃, 1000 h.
Exposed at -55±3℃, 96 h.
×
×
×
-
-
-
② No damage, crack and looseness of parts
Sulphur dioxide
Exposed at 40±2 C,
① Contact resistance: 70 m MAX
[JIS C 60068-2-42]
Relative humidity 80±5%
25±5 ppm for 96 h.
Solderability
Soldered at solder temperature,
245±0.3℃ for immersion duration,3±0.3 sec.
A new uniform coating of solder shall cover a
minimum of 95 % of the surface being
immersed.
×
×
-
-
Resistance to
soldering heat
1) Reflow soldering :
No deformation of case of excessive
looseness of the terminals. (note 3)
Peak TMP. 250 C MAX .
Reflow TMP. over 220 C 60 to 90 sec.
Number of reflow : 2 times
2) Soldering irons :
TMP. 400±10 C for 5±1 sec .
COUNT
DESCRIPTION OF REVISIONS
DESIGNED
CHECKED
DATE
0
△
REMARK
APPROVED
CHECKED
DESIGNED
DRAWN
HS.HIRAHARA
HS.HIRAHARA
YT.SASAKI
20240112
20240112
20240105
20240105
Unless otherwise specified, refer to IEC 60512.
YT.SASAKI
Note QT:Qualification Test AT:Assurance Test X:Applicable Test
DRAWING NO.
PART NO.
CODE NO.
ELC-380680-00-00
FH69-30S-0.5SH
SPECIFICATION SHEET
HIROSE ELECTRIC CO., LTD.
CL0580-5006-0-00
1/2
0
△
FORM HD0011-2-1