Application Tips for the ADS1210/11
last revision : 12/23/97
1. Data Sheet Clarification (PDS-1284C) - Resetting the ADS1210/11 (Slave Mode only),
Figure 27 (pg. 30) - This is a serial reset function for the A/D converter. The data sheet shows the time
sequence of a signal through SCLK which resets the A/D converter into its default condition. A
successful reset will give a 850Hz frequency output on the /DRDY pin (assuming a 10MHz clock at
Xin). The data sheet specifies the time sequence of T1, T2, T1, T2, T3, T2, T4 in Figure 27. The first
parameter, T1 should be T3. The correct sequence is T3, T2, T1, T2, T3, T2, T4.
2. Data Sheet Clarification (PDS-1284C) - Decimation Ratio Calculations (pg. 11) - In the
“DIGITAL FILTER” section of the data sheet there is a formula that is used to determine the correct
Decimation Ratio for a desired data rate. This formula is incorrect. It should be:
fDATA = (fXIN * Turbo Mode) / (512 * [Decimation Ratio +1])
which is equivalent to:
Decimation Ratio = ([fXIN * Turbo Mode] / [512 * fDATA ]) – 1
3. Data Sheet Clarification (PDS-1284C) - Calculating Effective Resolution in Bits vs.
Effective Resolution in Vrms with PGA gains greater than one (pg. 10) - The formulas for the
conversion from bits to Vrms on page 10 of the data sheet assume a PGA gain of one. These formulas
can be used for all PGA settings by changing the constant value of “10V” (in the numerator of both
equations) into a value of “10V / PGA”. To clarify these formulas, Effective Resolution is Bits is a
number that refers to the digital output of the A/D converter. Effective Resolution in Vrms is a voltage
and is referred to the input of the A/D converter. The second to last paragraph of page 10 is incorrect
and should be ignored.
4. Data Sheet Clarification (PDS-1284C) - Continuous Read Mode (pg. 29) : Add this text to
the last paragraph of this section - “Note that once /CS has been taken HIGH, the Continuous Read
Mode will be enabled (but not entered) and can never be disabled. The mode is actually entered and
exited as described previously.”
5. Data Sheet Clarification (PDS-1284C) - Application Circuits, Figure 43 and Figure 44 (pg.
38 and 39) - Pin 6 in the diagram is correctly labeled “AGND”, however, the connection to that pin
“DVDD” is incorrect. This pin should be connected to “AGND”.
6. Data Sheet Clarification (PDS-1284C) - I/O Recovery (pg. 32) - If serial communication
stops during an instruction or data transfer, the I/O port will reset itself. This occurs after 4 * tDATA
The data sheet states in this section that the device recovers after 8 * tDATA . This is an error.
.
7. Data Sheet Clarification (PDS-1284C) - Flowchart for Writing and Reading Register Data,
Slave Mode, Figure 26 (pg. 28) - In the right most flow chart, 5th box down (or second real looking
box), actually reads “External device generates 8 serial clock cycles and receives instruction register data
via SDIO” should read “… and TRANSMITS instruction register data via SDIO”.
8. Data Sheet Clarification (PDS-1284C) - CMR test conditions (pg. 2) - The common-mode
rejection test is performed with a 100mV differential input.
9. Commonly Asked Questions - What’s the best clock signal that I can provide for
the ADS1210 and ADS1211? - The ADS1210 and ADS1211 were characterized using CTS
5秒后页面跳转
NTC热敏电阻与PTC热敏电阻的应用原理及应用范围
GTO与普通晶闸管相比为什么可以自关断？为什么普通晶闸管不能呢？从GTO原理、应用范围带你了解原因及推荐型号
LF353数据手册解读：特性、应用、封装、引脚说明、电气参数及替换型号推荐
A4950资料手册解读：特性、应用、封装、引脚功能、电气参数及代换型号
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
