SOLID TANTALUM ELECTROLYTIC CAPACITORS
MUS E F9 5
Conformal coated Chip, For Mobile Audio
Specifications
Adapted to the RoHS directive (2002/95/EC).
Item
Performance Characteristics
Category
Temperature Range
--55 ~ +125 (Rated temperature : +85
)
˚C ˚C
Capacitance Tolerance ± 20% (at 120Hz)
Dissipation Factor
Refer to next page
(at 120Hz)
ESR(100kHz)
Refer to next page
After 1 minute's application of rated voltage, leakage current at 25 is not
more than 0.01CV or 0.5 µA, whichever is greater.
•
˚C
Leakage Current
+15% Max. (at +125
)
˚C
Capacitance Change
by Temperature
+10% Max. (at +85
--10% Max. (at --55
)
˚C
)
˚C
At 40 , 90 ~ 95% R.H., For 500 hours (No voltage applied)
˚C
Capacitance Change • • • • • • Refer to next page ( 1)
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • • Initial specified value or less
Damp Heat
At --55˚C / +125˚C, 30 minutes each, For 5 cycles,
Capacitance Change • • • • • • Refer to next page ( 1)
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • •• Initial specified value or less
Temperature Cycles
Reflow at 260 for 10 seconds
˚C
Applications
Mobile Audio Player
Digital video camcorder
Resistance to
Soldering Heat
Capacitance Change • • • • • • • • • Refer to next page ( 1)
Dissipation Factor • • • • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • •• • • • Initial specified value or less
Digital still camera
Mobile phone
After application of surge voltage in series with a 33
Ω resistor at the rate of 30
Feature
seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85
capacitors meet the characteristics requirements listed below.
Capacitance Change • • • • • • Refer to next page ( 1)
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • • Initial specified value or less
,
˚C
Rich sound in the bass register and clear sound,Materials
are strictly selected to achieve high level sound.
F95 series has no lead-frame, and no vibration factor.
Low ESR, Low ESL
Surge
Line up miniature size and high capacitance, necessary to
mobile design.
After 2000 hours' application of rated voltage at 85 , or derated voltage at
˚C
125 , capacitors meet the characteristic requirements listed below.
˚C
Capacitance Change • • • • • • Refer to next page ( 1)
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • •• Initial specified value or less
Endurance
Shear Test
After applying the pressure load of 5N
for 10± 1 seconds horizontally to the
center of capacitor side body which has
no electrode and has been soldered
beforehand on an aluminum substrate,
there shall be found neither exfoliation
Type numbering system (Example : 4V 220 µF)
•
5N (0.51kg f)
For 10 ± 1 seconds
nor its sign at the terminal electrode.
Keeping a capacitor surface-mounted on a substrate upside
down and supporting the substrate at both of the opposite
bottom points 45mm apart from the center of the capacitor,
the pressure strength is applied with
a specified jig at the center of the
20
R230
Terminal Strength
substrate so that the substrate may
bend by 1mm as illustrated. Then,
there shall be found no remarkable
45
45
abnormality on the capacitor terminals.
As for the surge and derated voltage at 125 , refer to page 266 for details.
˚C
(mm)
( D )
Dimensions
Drawing
case code
L
W
H
A
B
C
L
W
3.2 ± 0.3 1.6 ± 0.3 1.0 ± 0.2 0.8 ± 0.3 1.2 ± 0.3 0.8 ± 0.3
3.2 ± 0.3 1.7 ± 0.3 1.4 ± 0.2 0.8 ± 0.3 1.2 ± 0.3 0.8 ± 0.3
3.5 ± 0.2 2.7 ± 0.2 1.0 ± 0.2 0.8 ± 0.2 1.2 ± 0.2 1.1 ± 0.2
3.5 ± 0.2 2.8 ± 0.2 1.8 ± 0.2 0.8 ± 0.3 1.2 ± 0.3 1.1 ± 0.3
(0.2)
(0.2)
(0.2)
(0.2)
S
A
T
B
H
Resin
D dimension only for reference
Solder electrode
Solder electrode
(D)
A
B
C
Single-side electrodes
(Both electrodes at bottom side only)
CAT.8100V