EFST
preliminary
F49L004UA / F49L004BA
4 Mbit (512K x 8)
3V Only CMOS Flash Memory
1. FEATURES
!
!
!
Single supply voltage 2.7V-3.6V
!
Ready/Busy (RY/
)
BY
Fast access time: 70/90 ns
- RY/
output pin for detection of program or erase
BY
Compatible with JEDEC standard
- Pinout, packages and software commands
compatible with single-power supply Flash
Low power consumption
operation completion
End of program or erase detection
- Data polling
!
!
- Toggle bits
- 20mA typical active current
!
!
Hardware reset
- 0.2uA typical standby current
- Hardware pin(
) resets the internal state machine
RESET
!
!
10,000 minimum program/erase cycles
Command register architecture
to the read mode
Sector Protection /Unprotection
- Hardware Protect/Unprotect any combination of sectors
from a program or erase operation.
Low VCC Write inhibit is equal to or less than 2.0V
Boot Sector Architecture
- Byte programming (9us typical)
- Sector Erase(sector structure: one 16 KB, two 8 KB,
one 32 KB, and seven 64 KB)
!
!
!
Auto Erase (chip & sector) and Auto Program
- Any combination of sectors can be erased
concurrently; Chip erase also provided.
- Automatically program and verify data at specified
address
- U = Upper Boot Sector
- B = Bottom Boot Sector
!
Packages available:
- 40-pin TSOPI
!
Erase Suspend/Erase Resume
- Suspend or Resume erasing sectors to allow the
read/program in another sector
- 32-pin PLCC
2. ORDERING INFORMATION
Part No
Boot
Speed
Package
Part No
Boot
Speed
Package
F49L004UA-70T
F49L004UA-70N
F49L004BA-70T
F49L004BA-70N
Upper
Upper
Bottom
Bottom
70 ns
70 ns
70 ns
70 ns
TSOPI
PLCC
TSOPI
PLCC
F49L004UA-90 T
F49L004UA-90N
F49L004BA-90T
F49L004BA-90N
Upper
Upper
Bottom
Bottom
90 ns
90 ns
90 ns
90 ns
TSOPI
PLCC
TSOPI
PLCC
3. GENERAL DESCRIPTION
The F49L004UA/ F49L004BA is a 4 Megabit, 3V only
CMOS Flash memory device organized as 512K bytes of 8
bits. This device is packaged in standard 40-pin TSOP and
32-pin PLCC. It is designed to be programmed and erased
both in system and can in standard EPROM programmers.
The F49L004UA/ F49L004BA features a sector erase
architecture. The device memory array is divided into one
16 Kbytes, two 8 Kbytes, one 32 Kbytes, and seven 64
Kbytes. Sectors can be erased individually or in groups
without affecting the data in other sectors. Multiple-sector
erase and whole chip erase capabilities provide the
flexibility to revise the data in the device.
With access times of 70 ns and 90 ns, the F49L004UA/
F49L004BA allows the operation of high-speed
microprocessors. The device has separate chip enable
The sector protect/unprotect feature disables both
program and erase operations in any combination of the
sectors of the memory. This can be achieved in-system or
via programming equipment.
, write enable
, and output enable
controls.
OE
WE
CE
EFST's memory devices reliably store memory data even
after 100,000 program and erase cycles.
A low VCC
detector inhibits write operations on loss of
power. End of program or erase is detected by the
Ready/Busy status pin, Data Polling of DQ7, or by the
Toggle Bit I feature on DQ6. Once the program or erase
cycle has been successfully completed, the device
internally resets to the Read mode.
The F49L004UA/ F49L004BA is entirely pin and
command set compatible with the JEDEC standard for 4
Megabit Flash memory devices. Commands are written to
the command register using standard microprocessor write
timings.
Elite Flash Storage Technology Inc.
Publication Date : Aug. 2003
Revision: 0.2
1/46