DECOUPLING DEVICE FOR HIGH FREQUENCY
F1 1
Higher Capacitance.
Low ESR, Low ESL,High ripple current.
Resin-molded Chip.
Specifications
Item
Performance Characteristics
Designed for surface mounting on high density PC board.
+
°
Load life of 5000 hours at 105°C.
Category Temperature Range −55 to +105 C
Compliant to the RoHS directive (2002/95/EC).
Capacitance Tolerance ±20% (at 120Hz)
Dissipation Factor
ESR
Refer to next table
Refer to next table
After 5 minute’s application of rated voltage,
leakage current is not more than 0.1CV
Leakage Current
°
At 60 C 90%RH 500hours (No voltage applied)
..Within −20 to +30% of the initial specified value
Capacitance Change
.......
Damp Heat
(Steady State)
Dissipation Factor
200% or less than the Initial specified value
200% or less than the Initial specified value
Initial specified value or less
............................
ESR
Leakage Current
.........
°
°
−55 C / +105 C 30minutes each 5cycle
..
Capacitance Change Within ±20% of the Initial specified value
Dissipation Factor
ESR
Leakage Current
Temperature Cycles
.......
200% or less than the Initial specified value
200% or less than the Initial specified value
Initial specified value or less
............................
.........
Type numbering system (Example : 2.5V 220µF)
°
°
−55 C
+105 C
1
2
3
4
5
6
7
8
9
10 11 12 13 14
Capacitance Change Within −20 to +0%
Dissipation Factor Initial specified value or less 150% or less than the Initial specified value
Initial specified value or less 150% or less than the Initial specified value
Within −0 to +50%
Temperature Change
Characteristics
F 1 1 0 E 2 2 7 M D L A H
ESR
Low ESR
Leakage Current Initial specified value or less 10 times Initial specified value
Taping code
Capacitor meets the following characteristics after solder reflow
°
Reel Dia
(mm)
Tape width
(mm)
(Peak: 240
C for 10sec, 2cycle).
code
Temperature should be measured at the terminals.
Resistance
to Soldering Heat
L
16
24
φ180
φ330
..
Capacitance Change Within ±20% of the Initial specified value
Dissipation Factor
ESR
Leakage Current
K
.......
Initial specified value or less
Initial specified value or less
Initial specified value or less
............................
Case code
.........
Capacitance tolerance
Rated capacitance
Rated voltage
Series
After application of 115% of rating voltage at the rate of
30 seconds ON, 30 seconds OFF, for 1000 successive
test cycles at 105 C, capacitors meet the characteristics
°
requirements listed below.
Surge
....
Capacitance Change Within ±20% of the initial specified value
.........
..............................
...........
Dissipation Factor
ESR
Leakage Current
200% or less than the Initial specified value
200% or less than the Initial specified value
Initial specified value or less
Dimensions
L1
°
After 5000 hours’ application of rated voltage at 105 C, they will meet
the specified value for life charecteristics listed below.
....
Capacitance Change Within ±20% of the initial value
W2
Endurance
Marking
.........
Dissipation Factor
200% or less than the Initial specified value
200% or less than the Initial specified value
Initial specified value or less
W1
..............................
ESR
...........
Leakage Current
H
Printed on the package top.
P
S2
S3
S1
L2
(
mm)
Case Code
W1
7.3 ± 0.2 5.3 ± 0.2
15.6 ± 0.2
W2
L2
H
S1
S2
S3
P
L1
D
F
8.5 ± 0.2
1.7 ± 0.2
3.6 ± 0.2
2.0MAX. 0.9 ± 0.2 0.6 ± 0.2 0.5 ± 0.2 3.3 ± 0.2
2.5MAX. 1.5 ± 0.1 1.3 ± 0.1 1.5 ± 0.2 7.0 ± 0.2
16.7 ± 0.2
12.1 ± 0.2
Marking
Standard ratings
V
2.5
0E
4
0G
D
6.3
0J
D
Code
476
107
227
337
607
807
128
Cap.(
µ )
F
F case only
Seriese
47
F11
100
220
330
600
800
D
D
( )
D
D
( )
D
0E128M
Capacitance Tolerance
8J1234
Rated Capacitance
(Capacitance code)
( )
D
Rated Voltage
(Voltage code)
Lot No.
F
F
F
1200
F
(
)
The series in parentheses are being developed.
Please contact to your local Nichicon sales office when
these series are being designed in your application.
CAT.8100Y