Mono 2.9 W Class-D Audio Amplifier
with Digital Current and Voltage Output
SSM4321
Data Sheet
The SSM4321 features a high efficiency, low noise modulation
scheme that requires no external LC output filters. The modulation
scheme provides high efficiency even at low output power. The
SSM4321 operates with 89% efficiency at 1.4 W into 8 Ω from
a 5.0 V supply with an SNR of >100 dB.
FEATURES
Filterless Class-D amplifier with spread-spectrum
Σ-Δ modulation
Digitized output of output voltage, output current,
and PVDD supply voltage
72 dB signal-to-noise ratio (SNR) on output current sensing
and 77 dB SNR on output voltage sensing
TDM or multichip I2S slave output interface
Up to 4 chips supported on a single bus
8 kHz to 48 kHz operation
The SSM4321 includes circuitry to sense output current, output
voltage, and the PVDD supply voltage. Current sense is performed
using an external sense resistor that is connected between an
output pin and the load. The output current and voltage are sent
to ADCs with 16-bit resolution; the PVDD supply voltage is sent
to an ADC with 8-bit resolution.
The outputs of these ADCs are available on the TDM or I2S
output serial port. The SLOT pin is used to determine which of
four possible output slots is used on the TDM interface. A stereo
I2S interface can be selected by reversing the pin connections for
BCLK and FSYNC. Also, a direct PDM bit stream of voltage and
current data can be selected via the SLOT pin.
I2S/left justified slave output interface
1 or 2 chips supported on a single bus
8 kHz to 48 kHz operation
PDM output interface operates from 1 MHz to 6.144 MHz
2.2 W into 4 Ω load and 1.4 W into 8 Ω load at 5.0 V supply
with <1% total harmonic distortion plus noise (THD + N)
89% efficiency at 5.0 V, 1.4 W into 8 Ω + 0.2 Ω RSENSE speaker
>100 dB signal-to-noise ratio (SNR)
Spread-spectrum pulse density modulation (PDM) is used to
provide lower EMI-radiated emissions compared with other
Class-D architectures. The inherent randomized nature of
spread-spectrum PDM eliminates the clock intermodulation
(beating effect) of several amplifiers in close proximity.
High PSRR at 217 Hz: 86 dB
Amplifier supply operation from 2.5 V to 5.5 V
Input/output supply operation from 1.42 V to 3.6 V
Flexible gain adjustment pin: 0 dB to 12 dB in 3 dB steps
with fixed input impedance of 80 kΩ
<1 μA shutdown current
Smart power-down with loss of BCLK
Short-circuit and thermal protection with autorecovery
Available in a 16-ball, 0.4 mm pitch, 1.74 mm × 1.74 mm WLCSP
Pop-and-click suppression
The SSM4321 produces ultralow EMI emissions that significantly
reduce the radiated emissions at the Class-D outputs, particularly
above 100 MHz. The ultralow EMI emissions of the SSM4321 are
also helpful for antenna and RF sensitivity problems.
The device includes a highly flexible gain select pin that requires
only one series resistor to select a gain setting of 0 dB, 3 dB, 6 dB,
9 dB, or 12 dB. Input impedance is fixed at 80 kΩ, independent
of the selected gain.
APPLICATIONS
Mobile phones
MP3 players
Portable electronics
The SSM4321 has a shutdown mode with a typical shutdown
current of <1 μA. Shutdown is enabled by removing the BCLK
input. A clock must be present on the BCLK pin for the part
to operate.
GENERAL DESCRIPTION
The SSM4321 is a fully integrated, high efficiency, Class-D
audio amplifier with digitized output of output voltage, output
current, and the PVDD supply voltage. It is designed to maximize
performance for mobile phone applications. The application circuit
requires a minimum of external components and operates from
a 2.5 V to 5.5 V supply for the amplifier and a 1.42 V to 3.6 V
supply for input/output. The SSM4321 is capable of delivering
2.2 W of continuous output power with <1% THD + N driving
a 4 Ω load from a 5.0 V supply with a 0.1 Ω V/I sense resistor.
The device also includes pop-and-click suppression circuitry,
which minimizes voltage glitches at the output during turn-on
and turn-off, reducing audible noise on activation and deactivation.
The SSM4321 is specified over the industrial temperature range
of −40C to +85C. It has built-in thermal shutdown and output
short-circuit protection. It is available in a halide-free, 16-ball,
0.4 mm pitch, 1.74 mm × 1.74 mm wafer level chip scale package
(WLCSP).
Rev. 0
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Technical Support
©2012 Analog Devices, Inc. All rights reserved.
www.analog.com
5秒后页面跳转
英伟达新AI芯片Rubin或提前半年亮相
苹果iPhone 17将全系采用三星/LG显示LTPO OLED面板
三星深化印度制造布局，供应链本地化进程加速
芯擎科技“星辰一号”自动驾驶芯片点亮成功，2025年量产在即
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
