LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS
Inverter-use screw terminal, 85℃
RWK
RWHSeries
Higher ripple
RWH
Downsized and high ripple current from RWF series
・
・
・
Endurance with ripple current : 5,000 hours at 85
RoHS2 Compliant
℃
Downsized
Higher ripple
RWF
SPECIFICATIONS
◆
Items
Characteristics
Category
Temperature Range
-25 to +85
℃
Rated Voltage Range
Capacitance Tolerance
Leakage Current
350 to 450Vdc
20% (M)
I=0.02CV or 5mA, whichever is smaller.
(at 20 , 120Hz)
±
℃
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20 after 5 minutes)
℃
Dissipation Factor
0.25 max.
(at 20 , 120Hz)
(tan
)
℃
δ
Low Temperature
Characteristics
Capacitance change C(-25 )/C(+20
)
0.7
℃
℃ ≧
(at 120Hz)
Insulation Resistance
When measured between the terminals that are connected to each other and to the mounting clamp on the insulating sleeve covering
the case by using an insulation resistance meter of 500Vdc, the insulation resistance shall not be less than 100M
.
Ω
Insulation
Withstanding Voltage
When a voltage of 2,000Vac is applied for 1 minute between the terminals that are connected to each other and to the mounting clamp
on the insulating sleeve covering the case, there shall not be electrical damage.
Endurance
The following specifications shall be satisfied when the capacitors are restored to 20 after subjected to DC voltage with the rated
℃
ripple current is applied (the peak voltage shall not exceed the rated voltage) for 5,000 hours at 85
.
℃
Capacitance change
D.F. (tan
Leakage current
20% of the initial value
200% of the initial specified value
The initial specified value
≦±
≦
≦
)
δ
Useful life
The following specifications shall be satisfied when the capacitors are restored to 20 after subjected to DC voltage with the rated
℃
ripple current is applied (the peak voltage shall not exceed the rated voltage) for 8,000 hours at 85
.
℃
Capacitance change
D.F. (tan
Leakage current
Failure rate
30% of the initial value
≦±
)
300% of the initial specified value
The initial specified value
1%
δ
≦
≦
≦
Shelf Life
The following specifications shall be satisfied when the capacitors are restored to 20 after exposing them for 500 hours at 85 without
℃
℃
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change 20% of the initial value
D.F. (tan
≦±
)
200% of the initial specified value
The initial specified value
δ
≦
≦
Leakage current
DIMENSIONS (Screw-Mount) [mm]
Terminal Code : LG
◆
●
●
●
Mounting Clamp Code : B
Mounting Clamp Code : C
3600
3
A±1
W±1
Sleeve (PVC : Black)
450±50
6
300±50
Vent
8
J
G±1
L+4max.
Plastic disk
φD
63.5
76.2
89
E
K
F
J
φD
63.5
76.2
A
B
W
F
38.1 43.5 28.0 14.0
44.5 50.0 31.5 14.0
50.8 56.5 31.5 16.0
90.0 76.0 80.0 28.0
104.5 90.0 93.5 31.5
φ63.5, φ76.2 : G=6
φ89 : G=4
<Screw specifcations>
Plus hexagon-headed screw :M5×0.8×10
Maximum screw tightening torque :3.23Nm
* The screw and the mounting clamp are separately supplied and not attached to the product.
PART NUMBERING SYSTEM
◆
1
2
3
4
5
6
7
8
9
10
11 12 13
14
15 16 17
18
E R
W
H A A A L G N A A A M A A A U
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 6,800µF:682, 12,000µF:123)
Mounting clamp code (N, B, C)
Terminal code
Voltage code (ex. 350V:351, 400V:401)
Series code
Category
Please refer to "Product code guide (screw-mount terminal type)"
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
CAT. No. E1001Y 2024