SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS
Low ESR, 105℃
AIchipTM-MZSSeries
MZS
Downsizing and Lower ESR, 2,000hours at 105
・
・
・
・
・
・
℃
Rated voltage range : 25, 35V, Nominal capacitance range : 330 to 1,000μF
Solvent resistant type(see PRECAUTIONS AND GUIDELINES)
Vibration resistance structure
Higher capacitance
MZR
RoHS2 Compliant
AEC-Q200 compliant : Please contact Chemi-Con for more details, test data, information.
SPECIFICATIONS
◆
Items
Characteristics
Category
Temperature Range
-55 to +105
℃
Rated Voltage Range 25, 35Vdc
Capacitance Tolerance
Leakage Current
20% (M)
(at 20 , 120Hz)
℃
±
I=0.01CV or 3µA, whichever is greater.
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20 after 2 minutes)
℃
Dissipation Factor
Rated voltage (Vdc)
25V 35V
0.14 0.12
25V 35V
(tan
)
δ
tan (Max.)
(at 20 , 120Hz)
δ
℃
Low Temperature
Characteristics
(Max. Impedance Ratio)
Rated voltage (Vdc)
Z(-25 )/Z(+20
)
)
)
2
3
3
2
3
3
℃
℃
℃
℃
Z(-40 )/Z(+20
℃
Z(-55 )/Z(+20
(at 120Hz)
℃
Endurance
The following specifications shall be satisfied when the capacitors are restored to 20 after the rated voltage is applied for 2,000 hours
℃
at 105
.
℃
Capacitance change
D.F. (tan
Leakage current
30% of the initial value
200% of the initial specified value
The initial specified value
≦±
≦
≦
)
δ
Shelf Life
The following specifications shall be satisfied when the capacitors are restored to 20 after exposing them for 1,000 hours at 105 without
℃ ℃
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change 30% of the initial value
D.F. (tan
≦±
)
200% of the initial specified value
The initial specified value
δ
≦
≦
Leakage current
Surge Voltage Test
The capacitors shall be subjected to 1,000 cycles each consisting of charging with the specified surge voltage for 30 5 seconds through
±
a protective resistor (as required for RC=0.1 0.05sec) and open-circuiting for 5.5 minutes at a room temperature of 15 to 35
.
℃
±
Rated voltage (Vdc
Surge voltage (Vdc
)
)
25
29
35
40
Appearance
No significant damage
20% of the initial value
Capacitance change
D.F. (tan
≦±
)
200% of the initial specified value
The initial specified value
δ
≦
≦
Leakage current
(Caution)
Surge Voltage Test intends to evaluate capacitors in durability of an exceptional excessive voltage under specific conditions.It does
not imply long-term use at all.
DIMENSIONS [mm]
● Terminal Code : A
◆
● Terminal Code : G(Vibration resistant structure)
● Size code : HA0 and JA0
● Size code : HA0 and JA0
Size code
HA0
JA0
D
8
L
A
B
C
W
P
10.0 8.3 8.3 9.0 0.7 to 1.1 3.1
W
0.3max.
Vent for JA0
10 10.0 10.3 10.3 11.0 0.7 to 1.1 4.5
Vent for JA0
W
A±0.2
: Dummy terminals
L±0.5
0.3max.
L±0.5
A±0.2
MARKING
EX) 25V1,000µF
◆
● Rated voltage symbol
Rated voltage (Vdc)
Symbol
25
E
35
V
7Y
1000
EZS
Applying voltage over the rated voltages causes the capacitors to have short lifetime.
Besides, applying voltage over the specified surge voltages may cause to have short circuit failure. A protection
circuit should be used if applied voltage will exceed the rated voltages.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
CAT. No. E1001Y 2024