Photomicrosensor (Transmissive)
EE-SX493
I Dimensions
Note: All units are in millimeters unless otherwise indicated.
I Features
• Incorporates an IC chip with a built-in detector element and amplifier.
• Incorporates a detector element with a built-in temperature com-
pensation circuit.
• A wide supply voltage range: 4.5 to 16 VDC
• Directly connects with C-MOS and TTL.
• Allows highly precise sensing with a 0.2-mm-wide sensing aperture.
• RoHS Compliant.
6
0.2
I Absolute Maximum Ratings (Ta = 25°C)
9.5
6.5 0.05
Item
Symbol
Rated value
6.9 0.5
Pull-off
Emitter
Forward current
Reverse voltage
IF
50 mA (see note 1)
taper:
1/25
VR
4 V
Five, 0.5
max.
Five, 0.25
(1.25)
(1.25)
Detector
Power supply voltage VCC
16 V
28 V
16 mA
0.75 0.1
Cross section AA
Output voltage
Output current
VOUT
IOUT
Cross section BB
0
Two, 1 −0.2
(Tip dimension)
dia.
7
0.1
Permissible output
dissipation
POUT
250 mW
(see note 1)
Internal Circuit
K
A
V
Ambient
Operating
Storage
Topr
Tstg
Tsol
–40°C to 60°C
–40°C to 85°C
260°C (see note 2)
O
temperature
Unless otherwise specified, the
tolerances are as shown below.
G
Soldering temperature
Dimensions
3 mm max.
Tolerance
0.125
Terminal No.
Name
Anode
Cathode
Note: 1. Refer to the temperature rating chart if the ambient temper-
ature exceeds 25°C.
A
K
V
3 < mm ≤ 6
0.150
2. Complete soldering within 10 seconds.
Power supply
(Vcc)
6 < mm ≤ 10
10 < mm ≤ 18
18 < mm ≤ 30
0.180
I Ordering Information
0.215
O
G
Output (OUT)
Ground (GND)
0.260
Description
Model
EE-SX493
Photomicrosensor (transmissive)
I Electrical and Optical Characteristics (Ta = 25°C)
Item
Symbol
VF
IR
Value
1.2 V typ., 1.5 V max.
0.01 µA typ., 10 µA max.
940 nm typ.
Condition
Emitter
Forward voltage
Reverse current
IF = 20 mA
VR = 4 V
Peak emission wavelength λP
IF = 20 mA
Detector
Low-level output voltage
High-level output voltage
Current consumption
VOL
0.12 V typ., 0.4 V max.
15 V min.
VCC = 4.5 to 16 V, IOL = 16 mA, IF = 15 mA
VCC = 16 V, RL = 1 kΩ, IF = 0 mA
VCC = 16 V
VOH
ICC
λP
5 mA typ., 10 mA max.
870 nm typ.
Peak spectral sensitivity
wavelength
VCC = 4.5 to 16 V
LED current when output is OFF
LED current when output is ON
Hysteresis
IFT
10 mA typ., 15 mA max.
VCC = 4.5 to 16 V
∆H
15% typ.
3 kHz min.
3 µs typ.
VCC = 4.5 to 16 V (see note 1)
Response frequency
f
VCC = 4.5 to 16 V, IF = 15 mA, IOL = 16 mA (see note 2)
Response delay time
Response delay time
tPLH (tPHL
)
)
VCC = 4.5 to 16 V, IF = 15 mA, IOL = 16 mA (see note 3)
VCC = 4.5 to 16 V, IF = 15 mA, IOL = 16 mA (see note 3)
tPHL (tPLH
20 µs typ.
172
Photomicrosensor (Transmissive) EE-SX493