5秒后页面跳转
DTL22A PDF预览

DTL22A

更新时间: 2024-11-28 06:54:51
品牌 Logo 应用领域
村田 - MURATA 电子
页数 文件大小 规格书
4页 145K
描述
Voltage-Controlled 20 Amp 100 Watt, Electronic Loads

DTL22A 数据手册

 浏览型号DTL22A的Datasheet PDF文件第2页浏览型号DTL22A的Datasheet PDF文件第3页浏览型号DTL22A的Datasheet PDF文件第4页 
DTL Series  
s
DTL22A Model Voltage-Controlled  
20 Amp 100 Watt, Electronic Loads  
The DTL22A is an isolated (500Vdc), near-ideal (ZIN = ZOUT 10MΩ), analog/  
voltage-controlled current sink. Its 0-20A output/load current is straightforwardly  
"programmed" by applying a 0-10V input. The control signal can be generated by  
circuits as simple as the wiper of a trimpot or as sophisticated as programmable logic  
controllers (PLC’s) or analog-output computer I/O boards (D/A boards). The DTL22A  
supports any combination of IOUT = 0-20 Amps and VOUT = 2.5-50 Volts. Its thermally  
efficient, metal package, when properly heat sunk, can dissipate output/load power  
up to 100 Watts.  
The easy-to-use DTL22A is an excellent building block for low-cost, fully flexible,  
power-supply (AC/DC or DC/DC) or power-component (MOSFET’s, diodes, etc.) test  
and burn-in applications. It is accurate ( 5mA offset error, 1ꢀ overall accuracy),  
fast (200µsec full-scale step response), and capable of impressive resolution. If it is  
controlled with a 12-bit, 0-10V D/A converter, for example, one LSB (least significant  
bit) of the D/A corresponds to a 5mA change in the DTL22A’s output/load current.  
The DTL22A is packaged in a small (2" x 2" x 0.5"), thermally efficient metal  
package incorporating an aluminum baseplate with threaded inserts. It is powered by  
a single +5V supply and draws a mere 150mA.  
Features  
0-10V input/control voltage  
0-20A output/load current  
2.5-50V output compliance voltage  
0-100W output/load power  
10MΩ output impedance  
500Vdc isolation  
1ꢀ accuracy under all conditions  
200µsec full-scale step response  
2" x 2", shielded metal package  
Operate in parallel for higher power  
Applications  
Power-supply test and characterization  
Static/dynamic power-supply burn-in  
The DTL22A has an output compliance voltage of 2.5-50 Volts. Should the  
output/load voltage drop below the 2.5V required for proper biasing, an internal  
monitoring circuit activates the DTL22A’s output Fault line. See DATELs DTL22A-LC  
for compliance voltages as low as 0.6V.  
The DTL22A and other electronic loads, controller boards, and software from  
DATEL are outstanding building-block components for power-supply burn-in and test  
systems. They are extremely reliable, cost-effective solutions that enable you to  
quickly configure impressively accurate systems.  
Power-resistor substitution  
Real-time load simulation  
Capacitor discharge testing  
+5 VOLT  
SUPPLY  
+5 VOLT  
RETURN  
ISOLATED  
DC/DC  
ISOLATED  
DC/DC  
CONVERTER  
CONVERTER  
+LOAD  
+LOAD  
CONTROL  
VOLTAGE IN (+)  
+
AMPLIFIER  
CURRENT  
DRIVER  
CONTROL  
VOLTAGE IN (–)  
BUFFER  
AMPLIFIER  
ISOLATION  
AMPLIFIER  
–LOAD  
–LOAD  
ERROR  
DETECTION  
FAULT  
Figure 1. Simplified Schematic  
www.murata-ps.com  
Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000  
MDC_DTL22A.B01 Page 1 of 4  

与DTL22A相关器件

型号 品牌 获取价格 描述 数据表
DTL22A-LC MURATA

获取价格

Voltage-Controlled, 20 Amp 100 Watt, Low-Compliance Electronic Loads
DTL23A MURATA

获取价格

Voltage-Controlled, 2 Amp 100 Watt, Electronic Loads
DTL24A MURATA

获取价格

Voltage-Controlled, 10 Amp 100 Watt, Electronic Loads
DTL25A-LC MURATA

获取价格

Voltage-Controlled, 2 Amp 100 Watt, Low-Compliance Electronic Loads
DTL2A MURATA

获取价格

100 Watt, Digitally Programmable Serial-Input, Electronic Loads
DTL2A-LC MURATA

获取价格

100 Watt, Digitally Programmable Low-Voltage, Electronic Loads
DTL2N60 DINTEK

获取价格

Halogen-free According to IEC 61249-2-21
DTL2N60_13 DINTEK

获取价格

Power MOSFET Available in Tape and Reel
DTL3201 ETC

获取价格

TRANSISTOR | BJT | NPN | 40V V(BR)CEO | 10A I(C) | TO-210AC
DTL3202 ETC

获取价格

TRANSISTOR | BJT | NPN | 60V V(BR)CEO | 10A I(C) | TO-210AC