5秒后页面跳转
DS1075-IND PDF预览

DS1075-IND

更新时间: 2024-11-22 23:48:35
品牌 Logo 应用领域
其他 - ETC /
页数 文件大小 规格书
17页 324K
描述
EconOscillator/Divider

DS1075-IND 数据手册

 浏览型号DS1075-IND的Datasheet PDF文件第2页浏览型号DS1075-IND的Datasheet PDF文件第3页浏览型号DS1075-IND的Datasheet PDF文件第4页浏览型号DS1075-IND的Datasheet PDF文件第5页浏览型号DS1075-IND的Datasheet PDF文件第6页浏览型号DS1075-IND的Datasheet PDF文件第7页 
DS1075-IND  
EconOscillator/Divider  
www.dalsemi.com  
FEATURES  
PIN ASSIGNMENT  
§ Dual Fixed frequency outputs (30 kHz - 100  
MHz)  
I/O  
1
8
OSCIN  
OUT0  
VCC  
7
6
5
2
3
4
XTAL  
§ User-programmable on-chip dividers (from 1  
- 513)  
§ User-programmable on-chip prescaler (1, 2,  
4)  
§ No external components  
§ ±0.5% initial tolerance  
§ ±3% variation over temperature and voltage  
§ Internal clock, external clock or crystal  
reference options  
OE  
PDN/SELX  
GND  
DS1075Z 150-mil SOIC  
DS1075M-IND 300-mil DIP  
FREQUENCY OPTIONS  
Part No.  
Max O/P freq.  
DS1075-100 IND  
DS1075-80 IND  
DS1075-66 IND  
DS1075-60 IND  
100.000  
80.000  
66.667  
60.000  
§ Single 5V supply  
§ Power-down mode  
§ Synchronous output gating  
DESCRIPTION  
The DS1075-IND EconOscillator/Divider is a fixed frequency oscillator requiring no external  
components for operation. Numerous operating frequencies are possible in the range of approximately  
30kHz to 100 MHz through the use of an on-chip programmable prescaler and divider.  
The DS1075-IND features a master oscillator followed by a prescaler and then a programmable divider.  
The prescaler and programmable divider are user-programmable with the desired values being stored in  
non-volatile memory. This allows the user to buy an off the shelf component and program it on-site prior  
to board production. Design changes can be accommodated on the fly by simply programming different  
values into the device (or reprogramming previously programmed devices).  
The DS1075-IND is shipped from the factory configured for half the maximum operating frequency.  
Contact the factory for specially programmed devices. As alternatives to the on-board oscillator an  
external clock signal or a crystal may be used as a reference. The choice of reference source (internal or  
external) is user-selectable at the time of programming (or on the fly if the SEL mode is chosen).  
The DS1075-IND features a dual-purpose Input/Output pin. If the device is powered up in Program  
mode this pin can be used to input serial data to the on chip registers. After a Write command this data is  
stored in non-volatile memory. When the chip is subsequently powered up in operating mode these  
values are automatically restored to the on-chip registers and the Input/ Output pin becomes the oscillator  
output.  
The DS1075-IND is available in 8-pin DIP or SOIC packages, allowing the generation of a clock signal  
easily, economically and using minimal board area.  
1 of 17  
100199  

与DS1075-IND相关器件

型号 品牌 获取价格 描述 数据表
DS1075K ETC

获取价格

Oscillator Programming/Evaluation Kit
DS1075M DALLAS

获取价格

Microprocessor Circuit, CMOS, PDIP8, 0.300 INCH, DIP-8
DS1075M-100 DALLAS

获取价格

EconOscillator/Divider
DS1075M-100IND DALLAS

获取价格

Clock Generator, 100MHz, CMOS, PDIP8, 0.300 INCH, DIP-8
DS1075M-60 DALLAS

获取价格

EconOscillator/Divider
DS1075M-60IND DALLAS

获取价格

Clock Generator, 60MHz, CMOS, PDIP8, 0.300 INCH, DIP-8
DS1075M-60-IND DALLAS

获取价格

60MHz, OTHER CLOCK GENERATOR, PDIP8, 0.300 INCH, DIP-8
DS1075M-66 DALLAS

获取价格

EconOscillator/Divider
DS1075M-66IND DALLAS

获取价格

Clock Generator, 66.667MHz, CMOS, PDIP8, 0.300 INCH, DIP-8
DS1075M-66N MAXIM

获取价格

Analog Circuit, PDIP8, DIP-8