DML3006LFDS
SINGLE CHANNEL SMART LOAD SWITCH
Description and Applications
Features and Benefits
The DML3006LFDS load switch provides a component and area-
reducing solution for efficient power domain switching with inrush
current limit via soft−start. In addition to integrated control functionality
with ultra low on−resistance, this device offers system safeguards and
monitoring via fault protection and power good signaling. This cost
effective solution is ideal for power management and hot-swap
applications requiring low power consumption in a small footprint.
Advanced Controller with ChargePump
Integrated N-Channel MOSFET with Ultra Low RON
Input Voltage Range 0.5V to 13.5V
Soft-Start via Controlled SlewRate
Power Good Signal
Thermal Shutdown
VIN Under-VoltageLockout
Short-CircuitProtection
Portable Electronics and Systems
Extremely Low StandbyCurrent
Load Bleed (QuickDischarge)
Notebook and Tablet Computers
Telecom, Networking, Medical, and Industrial Equipment
Set−Top Boxes, Servers, and Gateways
Hot−Swap Devices and Peripheral Ports
Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2)
Halogen and Antimony Free. “Green” Device (Note 3)
V-DFN2020-8 (Type F)
Pin1
Top View
Bottom View
Top View
Ordering Information (Note 4)
Part Number
Case
Packaging
DML3006LFDS-7
3,000/Tape & Reel
V-DFN2020-8 (Type F)
Notes:
1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS), 2011/65/EU (RoHS 2) & 2015/863/EU (RoHS 3) compliant.
2. See https://www.diodes.com/quality/lead-free/ for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green" and
Lead-free.
3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and
<1000ppm antimony compounds.
4. For packaging details, go to our website at https://www.diodes.com/design/support/packaging/diodes-packaging/.
.
Pin Description
Pin Number
Pin Name
Pin Function
Drain of MOSFET (0.5V to 13.5V), Pin 1 must be connected to Pin 9
Active−high digital input used to turn on the MOSFET, pin has an internal pull down resistor to GND
Supply voltage to controller (3.0V to 5.5V)
1, 9
V
IN
2
3
EN
VCC
4
5
GND
BLEED
Controller ground
Load bleed connection, must be tied to VOUT through a resistor ≤ 1kΩ
Active−high, open−drain output that indicates when the gate of the MOSFET is fully charged,
external pull up resistor ≥1kΩ to an external voltage source required; tie to GND if not used.
Source of MOSFET connected to load
6
PG
7, 8
VOUT
1 of 9
www.diodes.com
March 2018
© Diodes Incorporated
DML3006LFDS
Document number: DS39172 Rev. 3 - 2
5秒后页面跳转
AO3401场效应管参数、引脚图、应用原理图
BT131可控硅参数及引脚图、工作原理详解
74LS32芯片参数、引脚图及功能真值表
全球首块英伟达H200交付 黄仁勋“送货上门”
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
