Applicable standard
Operating
Storage
temperature range
Storage
humidity range
Voltage
-55 C to +105C (Note1)
20% to 80% (Note2)
DF63-3S-3.96C
-10 C to +60C (Note3)
temperature range
Operating
Rating
40% to 70% (Note3)
humidity range
Applicable connector
AC/DC
630V
Current
AWG #16 : 15A
AWG #18 : 13A
AWG #20 : 11A
AWG #22 : 9A
Rated Voltage
600V AC/DC
Rated Current
See above
Overvoltage Category
IP-Degree
-
-
1
1
UL,C-UL
TÜV
300V AC/DC
See above
IP00
Ⅱ
Specifications
Test method
Item
Requirements
QT AT
Construction
General examination
Visually and by measuring instrument.
Confirmed visually.
According to drawing.
X
X
X
X
Marking
Electric characteristics
Contact resistance
10 m MAX.
-
-
-
20mV MAX, 1mA (DC or 1000Hz).
X
X
X
Insulation resistance
Voltage proof
500 V DC.
1000 M MIN.
1500 V AC for 1 min.
No flashover or breakdown.
Mechanical characteristics
Mechanical operation
30 times insertion and extraction.
①Contact resistance: 20 mΩ MAX.
②No damage, crack or looseness of parts.
①No electrical discontinuity of 1μs.
②No damage, crack or looseness of parts.
①No electrical discontinuity of 1μs.
②No damage, crack or looseness of parts.
-
-
-
X
X
X
Vibration
Frequency 10 to 55 Hz, single amplitude
0.75 mm, at 10 cycles for 3 direction.
Shock
490 m/s2 duration of pulse 11 ms at 3 times each for 3 both
axial directions.
Environmental characteristics
Damp heat
Exposed at 40 ± 2℃ , 90 to 95 %, 96 h.
①Contact resistance: 20 mΩ MAX.
②Insulation resistance: 500 M MIN.
③No damage, crack or looseness of parts.
①Contact resistance: 20 mΩ MAX.
②Insulation resistance: 1000 M MIN.
③No damage, crack or looseness of parts.
-
-
X
X
(Steady state)
(After leaving the room temperature for
1-2h.)
Rapid change of temperature Temperature -55℃→ +85℃
Time 30min→ 30min
Under 5 cycles.
(The transferring time of the tank is 2-3 min)
(After leaving the room temperature for 1-2h.)
1) Automatic soldering (Flow)
Soldered at solder temperature,
260c for in immersion , duration, 10 s.
2)Manual soldering
Soldering iron temperature :300℃,
Soldering time :3s.
No strength on contact.
Resistance to
Soldering heat
No deformation of case of excessive looseness of
the terminals.
X
X
-
-
Solderability
Soldered at solder temperature,
245c for in immersion , duration, 5 s.
A new uniform coating of solder shall cover
minimum of 95 of the surface being immersed.
Note 1: Include the temperature rising by current.
Note 2: No condensing
Note3: Apply to the condition of long term storage for unused products before mounted on PCB.
After mounted on PCB board , operating temperature and humidity range is applied for interim storage during transportation.
Count
Description of revisions
Designed
Checked
Date
1
2
DIS-H-00004228
TS.KUMAZAWA
SZ.ONO
18.09.20
17.02.14
17.02.14
17.02.13
17.02.13
△
Remarks
Approved
Checked
Designed
Drawn
HS.OKAWA
TS.FUKUSHIMA
YK.YAMAGUCHI
YK.YAMAGUCHI
Unless otherwise specified, refer to IEC 60512.
Note QT:Qualification Test AT:Assurance Test X:Applicable Test
Drawing no.
ELC-374389-00-00
DF63M-2P-7.92DS
Part no.
Specification sheet
1
△
1/1
Hirose electric co., ltd.
Code no.
CL680-0583-0-00
FORM HD0011-2-1