Applicable standard
Operating
Storage
temperature range
Storage
-55C to + 85C(Note 1)
-10C to + 60C(Note2)
temperature range
Operating
humidity range
20% to 80% (Note3)
1000V AC/DC
40% to 70%(Note2)
Rating
humidity range
Voltage
Applicable Connector
DF22 -*S-7.92C(28)
DF22#-*S-7.92C(#=B,C)
Current(*1)
Contact
1
2,3
4,5
Current(*2)
Contact
1
2,3
4,5
AWG10 43A/pin 38A/pin 33A/pin
AWG12 38A/pin 32A/pin 26A/pin
AWG14 26A/pin 23A/pin 22A/pin
AWG16 21A/pin 21A/pin 19A/pin
AWG10
30A/pin 25A/pin 22A/pin
25A/pin 20A/pin 18A/pin
20A/pin 18A/pin 15A/pin
15A/pin 15A/pin 13A/pin
AWG12
AWG14
AWG16
Overvoltage Category
Rated voltage
AC 600V
Rated current
See above(*1) (At ambient temp.25C)(Note 4)
IP-Protectio method
UL
―
―
C-UL
AC 600V
AC 600V
See above(*2) (Temp. rise up 30C MAX)
―
―
See above(*2)
Ⅱ
IPOO
TÜV
Specifications
Test method
Item
Requirements
QT AT
Construction
General examination
Visually and by measuring instrument.
Confirmed visually.
According to drawing.
X
X
X
X
Marking
Electric characteristics
Contact resistance
millivoltlevel method
20mV MAX, 1mA (DC OR 1000 Hz).
5 m MAX.
X
-
Insulation resistance
1000V DC.
1000M MIN.
X
X
-
-
Voltage proof
2500V AC for 1 min.
No flashover or breakdown.
Mechanical characteristics
Mechanical operation
50times insertions and extractions.
1) Contact resistance:
10m MAX.
-
X
X
X
2) No damage, crack or looseness of parts.
1) No electrical discontinuity of 1s.
2) No damage, crack or looseness of parts.
1) No electrical discontinuity of 1s.
2) No damage, crack or looseness of parts.
Vibration
Frequency 10 to 55 Hz, single amplitude
0.75 mm, at 2 h, for 3 directions.
490 m/s2 duration of pulse 11 ms at 3 times for 3
directions.
-
-
Shock
Environmental characteristics
Rapid change of
1) Contact resistance: 10m MAX.
2) Insulation resistance: 1000M MIN.
3) No damage, crack or looseness of parts.
Temperature -55→ 5 to 35→+85→ 5 TO 35 C
Time 30→ 5 MAX → 30→ 5 MAX min
X
X
X
temperature
-
-
-
Under 5 cycles.
Damp heat
(Steady state)
1) Contact resistance: 10m MAX.
2) Insulation resistance: 500M MIN.
3) No damage, crack or looseness of parts.
No deformation of case of excessive
looseness of the terminals.
Exposed at 40 ± 2 C, 90 to 95 , 96 h.
Resistance to
soldering heat
1) Solder bath method
Solder temperature : 260℃ for
Immersion,duration : 10 sec .
2) Manual soldering
Soldering iron temperature : 350℃
Soldering time : 3 sec.
No strength on contact.
Solderability
Remarks
Soldered at solder temperature,
245C for insertion duration, 5sec.
Solder shall cover a minimum of
95 of the surface being immersed.
X
-
Note1: Including the temperature rising by current.
Note2: No condensing.
Note3: Apply to the condition of long term storage for unused products before mounted on PCB.
After mounted on PCB, operation temperature and humidity range is applied for interim storage during transportation.
Note4: Indicates the current that corresponds to the RTI value (temperature at which performance is halved) of the resin when the ambient temperature is 25c.
Count
Description of revisions
Designed
Checked
Date
0
△
Unless otherwise specified, refer to IEC 60512.
Approved
Checked
Designed
Drawn
20200310
20200310
20200310
20200306
HS.OKAWA
SZ.ONO
SN.MIWA
DS.HIROWATARI
Note QT:Qualification Test AT:Assurance Test X:Applicable Test
Drawing no.
ELC-163719-53-00
DF22-*P-7.92DSA(53)
Part no.
Specification sheet
HIROSE ELECTRIC CO., LTD.
0
△
1/1
Code no.
CL680
FORM HD0011-2-1