CYW150
440BX AGPset Spread Spectrum Frequency Synthesizer
Table 1. Mode Input Table
Features
Mode
Pin 3
PCI_STOP#
REF0
• Maximized electromagnetic interference (EMI)
suppression using Cypress’s Spread Spectrum
technology
• Single-chip system frequency synthesizer for Intel®
440BX AGPset
0
1
Table 2. Pin Selectable Frequency
Input Address
CPU_F, 1:2
PCI_F, 0:5
• Three copies of CPU output
FS3 FS2 FS1 FS0
(MHz)
133.3
124
150
140
105
110
(MHz)
• Seven copies of PCI output
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
33.3 (CPU/4)
31 (CPU/4)
• One 48 MHz output for USB/one 24 MHz for SIO
• Two buffered reference outputs
• Two IOAPIC outputs
37.5 (CPU/4)
35 (CPU/4)
• 17 SDRAM outputs provide support for four DIMMs
• Supports frequencies up to 150 MHz
• SMBus interface for programming
• Power management control inputs
35 (CPU/3)
36.7 (CPU/3)
38.3 (CPU/3)
40 (CPU/3)
115
120
100
133.3
112
33.3 (CPU/3)
44.43 (CPU/3)
37.3 (CPU/3)
34.3 (CPU/3)
33.4 (CPU/2)
41.7 (CPU/2)
37.5 (CPU/2)
41.3 (CPU/3)
Key Specifications
CPU Cycle-to-Cycle Jitter: ..........................................250 ps
CPU to CPU Output Skew: .........................................175 ps
PCI to PCI Output Skew:.............................................500 ps
SDRAMIN to SDRAM0:15 Delay:.......................... 3.7 ns typ.
103
66.8
83.3
75
V
DDQ3:..................................................................... 3.3V±5%
DDQ2:..................................................................... 2.5V±5%
V
124
SDRAM0:15 (leads) to SDRAM_F Skew: ............. 0.4 ns typ.
[1]
Logic Block Diagram
Pin Configuration
VDDQ3
REF0/(PCI_STOP#)
VDDQ3
REF1/FS2
REF0/(PCI_STOP#)
GND
1
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
VDDQ2
IOAPIC0
IOAPIC_F
GND
2
REF1/FS2
X1
X2
XTAL
OSC
3
4
PLL Ref Freq
X1
5
CPU_F
CPU1
VDDQ2
CPU2
GND
VDDQ2
X2
6
Stop
Clock
Control
IOAPIC_F
VDDQ3
PCI_F/MODE
PCI0/FS3
GND
7
I/O Pin
Control
8
IOAPIC0
9
CLK_STOP#
SDRAM_F
VDDQ3
SDRAM0
SDRAM1
GND
SDRAM2
SDRAM3
SDRAM4
SDRAM5
VDDQ3
SDRAM6
SDRAM7
GND
CLK_STOP#
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
VDDQ2
CPU_F
PCI1
PCI2
Stop
Clock
PCI3
CPU1
CPU2
PCI4
Control
PLL 1
VDDQ3
PCI5
÷2,3,4
SDRAMIN
SDRAM11
SDRAM10
VDDQ3
SDRAM9
SDRAM8
GND
VDDQ3
PCI_F/MODE
PCI0/FS3
PCI1
Stop
Clock
Control
PCI2
PCI3
SDRAM15
SDRAM12
SDRAM13
VDDQ3
24MHz/FS0
48MHz/FS1
25
26
27
28
SDRAM14
SDATA
SCLK
SMBus
Logic
GND
PCI4
SDATA
SCLK
PCI5
VDDQ3
Note:
48MHz/FS1
1. 1.Internal pull-up resistors should not be relied upon for setting I/O pins HIGH. Pin function
with parentheses determined by MODE pin resistor strapping. Unlike other I/O pins, input
FS3 has an internal pull-down resistor.
PLL2
24MHz/FS0
VDDQ3
SDRAM0:15
Stop
Clock
Control
SDRAMIN
16
SDRAM_F
........................ Document #: 38-07177 Rev. *B Page 1 of 14
400 West Cesar Chavez, Austin, TX 78701 1+(512) 416-8500 1+(512) 416-9669
www.silabs.com