CY7C1566V18, CY7C1577V18
CY7C1568V18, CY7C1570V18
72-Mbit DDR-II+ SRAM 2-Word Burst
Architecture (2.5 Cycle Read Latency)
Features
Functional Description
■ 72-Mbit density (8M x 8, 8M x 9, 4M x 18, 2M x 36)
■ 400 MHz clock for high bandwidth
The CY7C1566V18, CY7C1577V18, CY7C1568V18, and
CY7C1570V18 are 1.8V Synchronous Pipelined SRAMs
equipped with DDR-II+ architecture. The DDR-II+ consists of an
SRAM core with advanced synchronous peripheral circuitry.
Addresses for read and write are latched on alternate rising
edges of the input (K) clock. Write data is registered on the rising
edges of both K and K. Read data is driven on the rising edges
of K and K. Each address location is associated with two 8-bit
words (CY7C1566V18), 9-bit words (CY7C1577V18), 18-bit
words (CY7C1568V18), or 36-bit words (CY7C1570V18) that
burst sequentially into or out of the device.
■ 2-word burst for reducing address bus frequency
■ Double Data Rate (DDR) interfaces
(data transferred at 800 MHz) at 400 MHz
■ Available in 2.5 clock cycle latency
■ Two input clocks (K and K) for precise DDR timing
❐ SRAM uses rising edges only
Asynchronous inputs include an output impedance matching
■ Echo clocks (CQ and CQ) simplify data capture in high-speed
systems
input (ZQ). Synchronous data outputs (Q, sharing the same
physical pins as the data inputs, D) are tightly matched to the two
output echo clocks CQ/CQ, eliminating the need for separately
capturing data from each individual DDR SRAM in the system
design.
■ Data valid pin (QVLD) to indicate valid data on the output
■ Synchronous internally self-timed writes
[1]
■ Core VDD = 1.8V ± 0.1V; IO VDDQ = 1.4V to VDD
All synchronous inputs pass through input registers controlled by
the K or K input clocks. All data outputs pass through output
registers controlled by the K or K input clocks. Writes are
conducted with on-chip synchronous self-timed write circuitry.
■ HSTL inputs and variable drive HSTL output buffers
■ Available in 165-Ball FBGA package (15 x 17 x 1.4 mm)
■ Offered in both Pb-free and non Pb-free packages
■ JTAG 1149.1 compatible test access port
■ Delay Lock Loop (DLL) for accurate data placement
Configurations
With Read Cycle Latency of 2.5 cycles:
CY7C1566V18 – 8M x 8
CY7C1577V18 – 8M x 9
CY7C1568V18 – 4M x 18
CY7C1570V18 – 2M x 36
Selection Guide
Description
Maximum Operating Frequency
Maximum Operating Current
400 MHz
375 MHz
375
333 MHz
333
300 MHz
300
Unit
MHz
mA
400
x8
x9
1400
1400
1400
1400
1300
1300
1300
1300
1200
1200
1200
1200
1100
1100
x18
x36
1100
1100
Note
1. The QDR consortium specification for V
is 1.5V + 0.1V. The Cypress QDR devices exceed the QDR consortium specification and are capable of supporting V
DDQ
DDQ
= 1.4V to V
.
DD
Cypress Semiconductor Corporation
Document Number: 001-06551 Rev. *E
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised March 11, 2008
[+] Feedback