CY7C1422JV18, CY7C1429JV18
CY7C1423JV18, CY7C1424JV18
36-Mbit DDR-II SIO SRAM 2-Word
Burst Architecture
Features
Functional Description
■
■
■
■
36 Mbit density (4M x 8, 4M x 9, 2M x 18, 1M x 36)
300 MHz clock for high bandwidth
The CY7C1422JV18, CY7C1429JV18, CY7C1423JV18, and
CY7C1424JV18 are 1.8V Synchronous Pipelined SRAMs,
equipped with Double Data Rate Separate I/O (DDR-II SIO)
architecture. The DDR-II SIO consists of two separate ports: the
read port and the write port to access the memory array. The
read port has data outputs to support read operations and the
write port has data inputs to support write operations. The DDR-II
SIO has separate data inputs and data outputs to completely
eliminate the need to “turn-around” the data bus required with
common I/O devices. Access to each port is accomplished
through a common address bus. Addresses for read and write
are latched on alternate rising edges of the input (K) clock. Write
data is registered on the rising edges of both K and K. Read data
is driven on the rising edges of C and C if provided, or on the
rising edge of K and K if C/C are not provided. Each address
location is associated with two 8-bit words in the case of
CY7C1422JV18, two 9-bit words in the case of CY7C1429JV18,
two 18-bit words in the case of CY7C1423JV18, and two 36-bit
words in the case of CY7C1424JV18 that burst sequentially into
or out of the device.
2-word burst for reducing address bus frequency
Double Data Rate (DDR) interfaces
(data transferred at 600 MHz) at 300 MHz
■
■
■
Two input clocks (K and K) for precise DDR timing
❐
SRAM uses rising edges only
Two input clocks for output data (C and C) to minimize clock
skew and flight time mismatches
Echo clocks (CQ and CQ) simplify data capture in high speed
systems
■
■
■
■
■
■
■
■
Synchronous internally self-timed writes
1.8V core power supply with HSTL inputs and outputs
Variable drive HSTL output buffers
Expanded HSTL output voltage (1.4V–VDD
)
Available in 165-Ball FBGA package (15 x 17 x 1.4 mm)
Offered in both Pb-free and non Pb-free packages
JTAG 1149.1 compatible test access port
Asynchronous inputs include an output impedance matching
input (ZQ). Synchronous data outputs are tightly matched to the
two output echo clocks CQ/CQ, eliminating the need to capture
data separately from each individual DDR-II SIO SRAM in the
system design. Output data clocks (C/C) enable maximum
system clocking and data synchronization flexibility.
Delay Lock Loop (DLL) for accurate data placement
Configurations
All synchronous inputs pass through input registers controlled by
the K or K input clocks. All data outputs pass through output
registers controlled by the C or C (or K or K in a single clock
domain) input clocks. Writes are conducted with on-chip
synchronous self-timed write circuitry.
CY7C1422JV18 – 4M x 8
CY7C1429JV18 – 4M x 9
CY7C1423JV18 – 2M x 18
CY7C1424JV18 – 1M x 36
Selection Guide
Description
300 MHz
300
267 MHz
267
250 MHz
250
Unit
MHz
mA
Maximum Operating Frequency
Maximum Operating Current
x8
x9
825
740
700
845
750
700
x18
x36
880
790
740
980
860
800
Cypress Semiconductor Corporation
Document #: 001-44699 Rev. *B
•
198 Champion Court
•
San Jose
,
CA 95134-1709
•
408-943-2600
Revised July 31, 2009
[+] Feedback