CY7C1318KV18/CY7C1320KV18
18-Mbit DDR II SRAM
Two-Word Burst Architecture
18-Mbit DDR II SRAM Two-Word Burst Architecture
Features
Configurations
■ 18-Mbit density (1M × 18, 512K × 36)
■ 333-MHz clock for high bandwidth
CY7C1318KV18 – 1M × 18
CY7C1320KV18 – 512K × 36
■ Two-word burst for reducing address bus frequency
Functional Description
■ Double data rate (DDR) interfaces (data transferred at
666 MHz) at 333 MHz
The CY7C1318KV18, and CY7C1320KV18 are 1.8
synchronous pipelined SRAM equipped with DDR II architecture.
The DDR II consists of an SRAM core with advanced
synchronous peripheral circuitry and a 1-bit burst counter.
Addresses for read and write are latched on alternate rising
edges of the input (K) clock. Write data is registered on the rising
edges of both K and K. Read data is driven on the rising edges
of C and C if provided, or on the rising edge of K and K if C/C are
not provided. On CY7C1318KV18 and CY7C1320KV18, the
burst counter takes in the least significant bit of the external
address and bursts two 18-bit words in the case of
CY7C1318KV18 and two 36-bit words in the case of
CY7C1320KV18 sequentially into or out of the device.
V
■ Two input clocks (K and K) for precise DDR timing
❐ SRAM uses rising edges only
■ Two input clocks for output data (C and C) to minimize clock
skew and flight time mismatches
■ Echo clocks (CQ and CQ) simplify data capture in high-speed
systems
■ Synchronous internally self-timed writes
■ DDR II operates with 1.5 cycle read latency when DOFF is
asserted HIGH
Asynchronous inputs include an output impedance matching
input (ZQ). Synchronous data outputs (Q, sharing the same
physical pins as the data inputs D) are tightly matched to the two
output echo clocks CQ/CQ, eliminating the need for separately
capturing data from each individual DDR SRAM in the system
design. Output data clocks (C/C) enable maximum system
clocking and data synchronization flexibility.
■ Operates similar to DDR-I device with 1 cycle read latency
when DOFF is asserted LOW
■ 1.8 V core power supply with HSTL inputs and outputs
■ Variable drive HSTL output buffers
■ Expanded HSTL output voltage (1.4 V–VDD
)
All synchronous inputs pass through input registers controlled by
the K or K input clocks. All data outputs pass through output
registers controlled by the C or C (or K or K in a single clock
domain) input clocks. Writes are conducted with on-chip
synchronous self-timed write circuitry.
❐ Supports both 1.5 V and 1.8 V I/O supply
■ Available in 165-ball FBGA package (13 × 15 ×1.4 mm)
■ Offered in both Pb-free and non Pb-free packages
■ JTAG 1149.1 compatible test access port
For a complete list of related documentation, click here.
■ Phase locked loop (PLL) for accurate data placement
Selection Guide
Description
Maximum operating frequency
333 MHz
333
300 MHz
300
250 MHz Unit
250
380
460
MHz
mA
Maximum operating current
× 18
× 36
450
430
560
520
Cypress Semiconductor Corporation
Document Number: 001-58905 Rev. *L
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised December 21, 2017