CY7C1021BNV33
64K x 16 Static RAM
Features
Functional Description[1]
• 3.3V operation (3.0V–3.6V)
The CY7C1021BNV is a high-performance CMOS static RAM
organized as 65,536 words by 16 bits. This device has an
automatic power-down feature that significantly reduces
power consumption when deselected.
• High speed
— tAA = 10, 12, 15 ns
• CMOS for optimum speed/power
• Low Active Power (L version)
— 576 mW (max.)
Writing to the device is accomplished by taking Chip Enable
(CE) and Write Enable (WE) inputs LOW. If Byte Low Enable
(BLE) is LOW, then data from I/O pins (I/O1 through I/O8), is
written into the location specified on the address pins (A0
through A15). If Byte High Enable (BHE) is LOW, then data
from I/O pins (I/O9 through I/O16) is written into the location
specified on the address pins (A0 through A15).
• Low CMOS Standby Power (L version)
— 1.80 mW (max.)
• Automatic power-down when deselected
• Independent control of upper and lower bits
• Available in 44-pin TSOP II and 400-mil SOJ
• Available in a 48-Ball Mini BGA package
Reading from the device is accomplished by taking Chip
Enable (CE) and Output Enable (OE) LOW while forcing the
Write Enable (WE) HIGH. If Byte Low Enable (BLE) is LOW,
then data from the memory location specified by the address
pins will appear on I/O1 to I/O8. If Byte High Enable (BHE) is
LOW, then data from memory will appear on I/O9 to I/O16. See
the truth table at the back of this data sheet for a complete
description of read and write modes.
The input/output pins (I/O1 through I/O16) are placed in a
high-impedance state when the device is deselected
(CE HIGH), the outputs are disabled (OE HIGH), the BHE and
BLE are disabled (BHE, BLE HIGH), or during a write
operation (CE LOW, and WE LOW).
The CY7C1021BNV is available in 400-mil-wide SOJ,
standard 44-pin TSOP Type II, and 48-ball mini BGA
packages.
Logic Block Diagram
Pin Configurations
SOJ / TSOP II
DATA IN DRIVERS
Top View
44
1
A
A
5
4
43
42
41
40
39
38
A
A
6
2
3
4
5
6
3
A
A
2
7
A7
A6
OE
A
1
BHE
BLE
I/O
A
0
A5
A4
A3
A2
64K x 16
CE
I/O1–I/O8
RAM Array
512 X 2048
I/O
7
1
16
37
36
35
34
33
I/O
I/O
8
I/O
I/O
I/O
2
3
15
14
13
I/O9–I/O16
9
A1
A0
10
11
12
13
I/O
4
VSS
VCC
VSS
VCC
I/O
I/O
I/O
I/O
32
I/O
5
12
11
10
9
31
30
29
28
I/O
6
14
15
16
I/O
7
COLUMN DECODER
I/O
8
WE 17
NC
18
27
26
25
A
A
8
15
BHE
19
A
A
14
9
WE
CE
OE
A
A
12
NC
20
21
22
A
11
NC
13
10
A
24
23
BLE
Note:
1. For guidelines on SRAM system design, please refer to the ‘System Design Guidelines’ Cypress application note, available on the internet at www.cypress.com
Cypress Semiconductor Corporation
Document #: 001-06433 Rev. *B
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised December 14, 2010
[+] Feedback