CY62146G/CY62146GE
CY62146GSL/CY62146GESL MoBL®
4-Mbit (256K words × 16 bit) Static RAM
with Error-Correcting Code (ECC)
4-Mbit (256K words
× 16 bit) Static RAM with Error-Correcting Code (ECC)
devices are accessed by asserting both chip enable inputs – CE1
as low and CE2 as HIGH.
Features
■ High speed: 45 ns/55 ns
Data writes are performed by asserting the Write Enable (WE)
input LOW, while providing the data on I/O0 through I/O15 and
address on A0 through A17 pins. The Byte High Enable (BHE)
and Byte Low Enable (BLE) inputs control write operations to the
upper and lower bytes of the specified memory location. BHE
controls I/O8 through I/O15 and BLE controls I/O0 through I/O7.
■ Ultra-low standby power
❐ Typical standby current: 3.5 A
❐ Maximum standby current: 8.7 A
■ Embedded ECC for single-bit error correction[1]
■ Widevoltage range: 1.65 V to2.2 V, 2.2 V to 3.6 V, 4.5 V to 5.5 V
■ 1.0-V data retention
Data reads are performed by asserting the Output Enable (OE)
input and providing the required address on the address lines.
Read data is accessible on the I/O lines (I/O0 through I/O15).
Byte accesses can be performed by asserting the required byte
enable signal (BHE or BLE) to read either the upper byte or the
lower byte of data from the specified address location.
■ TTL-compatible inputs and outputs
■ Error indication (ERR) pin to indicate 1-bit error detection and
correction
■ Pb-free 48-ball VFBGA and 44-pin TSOP II packages
All I/Os (I/O0 through I/O15) are placed in a HI-Z state when the
device is deselected (CE HIGH for a single chip enable device
and CE1 HIGH/CE2 LOW for a dual chip enable device), or
control signals are deasserted (OE, BLE, BHE).
Functional Description
CY62146G/CY62146GE and CY62146GSL/CY62146GESL are
high-performance CMOS low-power (MoBL) SRAM devices with
embedded ECC. Both devices are offered in single and dual chip
enable options and in multiple pin configurations. The
CY62146GE/CY62146GESL device includes an ERR pin that
signals an error-detection and correction event during a read
cycle. The CY62146GSL/CY62146GESL[1] device supports a
wide voltage range of 2.2 V–3.6 V and 4.5 V–5.5 V.
On the CY62146GE/CY62146GESL devices, the detection and
correction of a single-bit error in the accessed location is
indicated by the assertion of the ERR output (ERR = HIGH)[2]
.
See
the
Truth
Table
–
CY62146G/CY62146GE/CY62146GSL/CY62146GESL
page 17 for a complete description of read and write modes.
on
The logic block diagrams are on page 2.
Devices with a single chip enable input are accessed by
asserting the chip enable (CE) input LOW. Dual chip enable
Product Portfolio
Power Dissipation
Operating ICC, (mA)
Features and
Options
(see the Pin
Configurations
section)
Standby, ISB2 (µA)
Product[3]
Range
VCC Range (V) Speed (ns)
f = fmax
Typ[4]
Max
Typ[4]
Max
CY62146G(E)18
CY62146G(E)30
CY62146G(E)
Industrial
1.65 V–2.2 V
2.2 V–3.6 V
4.5 V–5.5 V
55
45
15
15
20
20
3.5
3.5
10
Single or dual
Chip Enables
8.7
Optional ERR
pin
CY62146G(E)SL[5]
2.2 V–3.6 V and
4.5 V–5.5 V
Notes
1. Datasheet specifications are not guaranteed for V in the range of 3.6 V to 4.5 V.
CC
2. This device does not support automatic write-back on error detection.
3. The ERR pin is available only for devices which have ERR option “E” in the ordering code. Refer Ordering Information for details.
4. Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at V = 1.8 V (for a V range of 1.65 V–2.2 V),
CC
CC
V
= 3 V (for V range of 2.2 V–3.6 V), and V = 5 V (for V range of 4.5 V–5.5 V), T = 25 °C.
CC
CC
CC
CC
A
5. Datasheet specifications are not guaranteed for V in the range of 3.6 V to 4.5 V.
CC
Cypress Semiconductor Corporation
Document Number: 001-95420 Rev. *E
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised April 26, 2017