REV COUNT DESCRIPTION OF REVISIONS
BY
CHKD DATE
REV COUNT DESCRIPTION OF REVISIONS
BY
KYG
KYI
CHKD DATE
18.03.16
21.08.23
-
-
Revised
Revised
BJH
HMY
LHJ
-
-
Revised
Revised
LHJ
1
2
3
4
18.04.09
21.12.16
LHJ
LHJ
Universal Serial Bus Type-C Cable and Connector Specification Release 2.1
Universal Serial Bus Type-C Connectors and Cable Assemblies Compliance Document Revision 2.1b
APPLICABLE STANDARD
CURRENT
VOLTAGE
1.25A Max. for each power pin (A1, A4, A9, A12, B1, B4, B5, B9, B12)
0.25A for the other pins
RATING
48V AC/DC
-40℃ ~ +105℃ (INCLUDING TEMP. RISE), 95% RH max. (NON-CONDENSING)
-10℃ ~ +60℃ (WITH PACKING), 15% ~ 70% RH
OPERATING CONDITION
STORAGE CONDITION
Para.
1
Test Description
Test Procedure
Test Requirement
QTAT
O O
EIA 364-18
Visual inspection
No physical damage.
Examination of product
Electrical Requirements
EIA 364-23
Measure at 20mV max open circuit
at 100mA (DC OR 1000Hz).
Low Level Contact
Resistance
Initial : 40mΩ max for each contact
2
O
-
4-wire measurement is required and
the resistance of PCB termination
shall be deducted from the reading.
After test : 50mΩ max for each contact
EIA 364-20
Measure per Method B with
unmated condition.
Dielectric
Withstanding Voltage
No disruptive discharge.
3
O
O
-
-
100V AC RMS for 1minute at sea level.
EIA 364-21
500V DC with unmated and mated condition.
100MΩ min.
4
Insulation Resistance
Mechanical Requirements
EIA 364-13
Measure at 12.5mm/minute min.
Initial & after test : 5N ~ 20N
(with virgin plug)
5
6
Insertion force
O
O
-
-
EIA 364-13
Measure at 12.5mm/minute min.
Initial : 8N ~ 20N
Extraction force
After test : 6N ~ 20N (with virgin plug)
EIA 364-09
Mated 10,000 times
Mechanically operated : 500cycles/hr
Mating stroke : 2.75mm
No physical damage.
7
Durability
O
-
Insertion, extraction force shall be measured
at a maximum speed of 12.5mm/min
Input air pressure : 20±5% KPa for 5sec.
Inspection leakage : 0.3% (60Pa) max.
No water penetration.
8
9
Air-Leak
IPX8
O
O
-
-
Immersion in the water
at the depth of 1.5m for 30min.
EIA 364-28
Test Condition VII, Test Letter D
Mated specimens to 3.10 G's RMS
between 20 to 500Hz
No physical damage.
No discontinuity of 1us of longer
duration when mated connector
during test.
10
Random Vibration
O
-
15minutes in each of 3 mutually
perpendicular planes.
REMARKS
DRAFT
DESIGN
CHECK
APPROVAL
RELEASE
DEPT
21.12.16
S.H.LIM
S.H.LIM
H.J.LEE
T.S.KANG
18.02.19
ENG
18.02.19
18.02.19
18.02.19
NOTE) QT : QUALIFICATION TEST, AT : ASSURANCE TEST, O : Applicable Test
DWG NO CL NO
PART NO
CX90MWD2-24P
ELC4-632534
CL 6240-0016-6
1
HIROSE KOREA.CO.,LTD
PRODUCT SPECIFICATION
3