CHKD
LHJ
LHJ
LHJ
CHKD
LHJ
Rev.
Count
Description of rev.
Preliminary drawing
Preliminarydrawing(RE-2-2167)
Released(RE-2-2337)
BY
Date
Rev.
3
Count
4
Description of rev.
EC(RE-2-2376)
BY
Date
0
1
2
-
1
3
KYG
KYG
KYG
22.12.20
23.03.06
23.07.24
OSW
230905
Universal Serial Bus Type-C Connectors and Cable Assemblies Compliance Document Revision 2.1b
48V AC/DC
Applicable standard
Voltage
Rating
1.25A max. for each power pin (i.e., A1, A4, A9, A12, B1, B4, B5, B9, B12)
0.25A max. for the others.
Current
Operating condition
Storage condition
-40℃~+105℃(Including temp. rise), 95% RH max.(Non-condensing)
-10℃~+60℃(With packing), 15%~70% RH
SPECIFICATIONS
No
TEST ITEM
TEST METHOD
TEST REQUIREMENT
No physical damage
QT
O
AT
O
CONSTRUCTION
General examination
EIA 364-18
Visual inspection
1
ELECTRICAL CHARACTERISTICS
EIA 364-23
Measure at 20mV max open circuit
at 100mA max. (DC or 1000Hz)
Low level contact
Initial : 40mΩ max
2
O
-
resistance
4-wire measurement is required and
the resistance of PCB termination
shall be deducted from the reading.
After test : 50mΩ max
EIA 364-20
Dielectric withstanding
Measure per Method B with
unmated condition.
No disruptive discharge.
3
O
O
-
-
voltage
100V AC RMS for 1 minute at sea level.
EIA 364-21
Insulation resistance
Temperature rise
100MΩ min.
4
5
500V DC with unmated and mated condition.
IEC60529, EIA-364-70, method B :
A current of 5.0 A shall be applied collectively to VBUS pins
(i.e., pins A4, A9, B4, and B9) and 1.25 A applied to the Vconn
pin (i.e., B5 of the plug connector) with the return path through
the corresponding GND pins (i.e., pins A1, A12, B1, and B12). A
minimum current of 0.25 A shall also be applied individually to
all the other contacts.
Temperature rise shall not exceed
O
-
30℃
No
TEST ITEM
TEST METHOD
TEST REQUIREMENT
QT
AT
MECHANICAL CHARACTERISTICS
EIA 364-13
Measure at 12.5mm/minute min.
Insertion force
Initial & after test : 5N ~ 20N
6
7
O
O
-
-
Initial : 8N ~ 20N
After test : 6N ~ 20N (with virgin
plug)
EIA 364-13
Measure at 12.5mm/minute min.
Extraction force
EIA 364-09
Mated 10,000 times
Mechanically operated : 500cycles/hr
Mating stroke : 2.75mm
Durability
No physical damage.
8
O
-
Insertion, extraction force shall be measured
at a maximum speed of 12.5mm/min
Remarks
Drawn
Y.G.KIM
22.12.20
Designed
Checked
Y.B.PARK
22.12.20
Approved
H.J.LEE
22.12.20
Release
ENG
23.09.05
DEPT
Y.G.KIM
22.12.20
[Note] QT : Qualification test, AT : Assurance test, O : Applicable, - : Not applicable
Drawing No. CL No.
Part No.
ELC4-633753-00
CL ****-****-*-***
CX90BW1-24P*
PRODUCT SPECIFICATION
1
HIROSE KOERA.CO.,LTD
5