CHKD
LHJ
LHJ
LHJ
CHKD
LHJ
Rev.
Count
Description of rev.
EC(RE-2-1937)
EC(RE-2-2167)
EC(RE-2-2337)
BY
Date
Rev.
4
Count
4
Description of rev.
EC(RE-2-2376)
BY
Date
1
2
3
4
2
3
JMS
KYG
KYG
22.06.01
23.03.06
23.07.24
OSW
230905
Universal Serial Bus Type-C Cable and Connector Specification Release 2.1
Universal Serial Bus Type-C Connectors and Cable Assemblies Compliance Document Revision 2.1b
Applicable standard
Voltage
Current
Operating condition
1 48V AC/DC
1
1.25A max. for each power pin (i.e., A1, A4, A9, A12, B1, B4, B9, B12)
1.25A max. for Vconn pin (i.e., B5)
Rating
0.25A. for the others.
-40℃~+105℃(Including temp. rise), 95% RH max.(Non-condensing)
-10℃~+60℃(With packing), 15%~70% RH
Storage condition
SPECIFICATIONS
No
TEST ITEM
TEST METHOD
TEST REQUIREMENT
No physical damage.
QT
O
AT
O
CONSTRUCTION
EIA 364-18
Visual inspection
Examination of product
1
ELECTRICAL CHARACTERISTICS
EIA 364-23
Measure at 20mV max open circuit
at 100mA max. (DC or 1000Hz)
Low Level Contact
Initial : 40mΩ max
4-wire measurement is required and
the resistance of PCB termination
shall be deducted from the reading.
2
O
-
Resistance
After test : 50mΩ max
EIA 364-20
Measure per Method B with
unmated condition.
Dielectric Withstanding
No disruptive discharge.
3
O
O
-
-
Voltage
100V AC RMS for 1 minute at sea level.
EIA 364-21
Insulation Resistance
Temperature Rise
500V DC with unmated and mated condition.
100MΩ min.
4
5
IEC60529, EIA-364-70, method B :
A current of
5.0 A shall be applied collectively to VBUS
1
pins ( i.e., pins A4, A9, B4, and B9) and 1.25 A applied to the
Vconn pin (i.e., B5 of the plug connector) with the return path
through the corresponding GND pins (i.e., pins A1, A12, B1,
and B12). A minimum current of 0.25 A shall also be applied
individually to all the other contacts.
Temperature rise shall not exceed
O
-
30℃
MECHANICAL CHARACTERISTICS
EIA 364-13
Measure at 12.5mm/minute min.
Initial & after test :
5N ~ 20N
Insertion force
6
7
O
O
-
-
Initial : 8N ~ 20N
After test : 6N ~ 20N (with virgin
plug)
EIA 364-13
Measure at 12.5mm/minute min.
Extraction force
EIA 364-09
Mated 10,000 times
Mechanically operated : 500cycles/hr
Mating stroke : 2.75mm
Durability
No physical damage.
8
O
-
Insertion, extraction force shall be measured at a maximum
speed of 12.5mm/min
Remarks
Drawn
Y.B.PARK
21.08.05
Designed
Checked
H.J.LEE
21.08.05
Approved
H.J.LEE
21.08.05
Release
DEPT
23.09.05
ENG
Y.B.PARK
21.08.05
[Note] QT : Qualification test, AT : Assurance test, O : Applicable, - : Not applicable
Drawing No. CL No.
Part No.
ELC4-633131-00
CL ****-****-*-***
CX90BW-16P*
PRODUCT SPECIFICATION
1
HIROSE KOERA.CO.,LTD
5