CD4066BMS
CMOS Quad Bilateral Switch
December 1992
Features
Description
• For Transmission or Multiplexing of Analog or Digital CD4066BMS is a quad bilateral switch intended for the
Signals
transmission or multiplexing of analog or digital signals. It is
pin for pin compatible with CD4016B, but exhibits a much
lower on state resistance. In addition, the on-state resistance
is relatively constant over the full input signal range.
• High Voltage Types (20V Rating)
• 15V Digital or ±7.5V Peak-to-Peak Switching
• 125Ω Typical On-State Resistance for 15V Operation
The CD4066BMS consists of four independent bilateral
switches. A single control signal is required per switch. Both
the p and the n device in a given switch are biased on or off
simultaneously by the control signal. As shown in Figure 1,
the well of the n channel device on each switch is either tied
to the input when the switch is on or to VSS when the switch
is off. This configuration eliminates the variation of the switch
transistor threshold voltage with input signal, and thus keeps
the on-state resistance low over the full operating signal
range.
• Switch On-State Resistance Matched to Within 5Ω
Over 15V Signal Input Range
• On-State Resistance Flat Over Full Peak-to-Peak Sig-
nal Range
• High On/Off Output Voltage Ratio
- 80dB Typ. at FIS = 10kHz, RL = 1kΩ
• High Degree of Linearity: <0.5% Distortion Typ. at
FIS = 1kHz, VIS = 5Vp-p, VDD - VSS ≥ 10V, RL = 10kΩ
The advantages over single channel switches include peak
input signal voltage swings equal to the full supply voltage,
and more constant on-state impedance over the input signal
range. For sample and hold applications, however, the
CD4016B is recommended.
• Extremely Low Off-State Switch Leakage Resulting in
Very Low Offset Current and High Effective Off-State
Resistance: 10pA Typ. at VDD - VSS = 10V, TA = +25oC
• Extremely High Control Input Impedance (Control Cir-
The CD4066BMS is supplied in these 14-lead outline pack-
ages:
cuit Isolated from Signal Circuit): 1012Ω Typ.
• Low Crosstalk Between Switches: -50dB Typ. at FIS =
8MHz, RL = 1kΩ
Braze Seal DIP
Frit Seal DIP
H4Q
H1B
• Matched
Control
Input
to
Signal
Output
Ceramic Flatpack H3W
Capacitance: Reduces Output Signal Transients
• Frequency Response, Switch on = 40MHz (Typ.)
• 100% Tested for Quiescent Current at 20V
• 5V, 10V and 15V Parametric Ratings
Pinout
CD4066BMS
TOP VIEW
• Meets All Requirements of JEDEC Tentative Standard
No. 13B, “Standard Specifications for Description of
“B” Series CMOS Devices”
IN/OUT A
OUT/IN A
OUT/IN B
IN/OUT B
CONT B
CONT C
VSS
1
2
3
4
5
6
7
14 VDD
13 CONT A
12 CONT D
11 IN/OUT D
10 OUT/IN D
Applications
• Analog Signal Switching/Multiplexing
- Signal Gating
- Squelch Control
- Chopper
- Modulator
- Demodulator
9
8
OUT/IN C
IN/OUT C
- Commutating Switch
• Digital Signal Switching/Multiplexing
• Transmission Gate Logic Implementation
• Analog to Digital & Digital to Analog Conversion
• Digital Control of Frequency, Impedance, Phase, and
Analog Signal Gain
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
File Number 3319
1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999
7-966