5秒后页面跳转
CD4066BM96E4 PDF预览

CD4066BM96E4

更新时间: 2024-02-16 17:11:19
品牌 Logo 应用领域
德州仪器 - TI 复用器开关复用器或开关信号电路光电二极管输出元件
页数 文件大小 规格书
20页 545K
描述
CMOS QUAD BILATERAL SWITCH

CD4066BM96E4 技术参数

是否无铅: 不含铅是否Rohs认证: 符合
生命周期:Active零件包装代码:SOIC
包装说明:SOIC-14针数:14
Reach Compliance Code:compliantHTS代码:8542.39.00.01
Factory Lead Time:6 weeks风险等级:5.05
Is Samacsys:N模拟集成电路 - 其他类型:SPST
标称带宽:40 MHzJESD-30 代码:R-PDSO-G14
JESD-609代码:e4长度:8.65 mm
湿度敏感等级:1标称负供电电压 (Vsup):-5 V
正常位置:NO信道数量:4
功能数量:4端子数量:14
通态电阻匹配规范:15 Ω最大通态电阻 (Ron):1050 Ω
最高工作温度:125 °C最低工作温度:-55 °C
输出:SEPARATE OUTPUT封装主体材料:PLASTIC/EPOXY
封装代码:SOP封装等效代码:SOP14,.25
封装形状:RECTANGULAR封装形式:SMALL OUTLINE
峰值回流温度(摄氏度):260电源:5/15 V
认证状态:Not Qualified座面最大高度:1.58 mm
最大信号电流:0.025 A子类别:Multiplexer or Switches
最大供电电流 (Isup):0.03 mA最大供电电压 (Vsup):18 V
最小供电电压 (Vsup):3 V标称供电电压 (Vsup):5 V
表面贴装:YES最长断开时间:70 ns
最长接通时间:70 ns切换:BREAK-BEFORE-MAKE
技术:CMOS温度等级:MILITARY
端子面层:Nickel/Palladium/Gold (Ni/Pd/Au)端子形式:GULL WING
端子节距:1.27 mm端子位置:DUAL
处于峰值回流温度下的最长时间:NOT SPECIFIED宽度:3.91 mm
Base Number Matches:1

CD4066BM96E4 数据手册

 浏览型号CD4066BM96E4的Datasheet PDF文件第2页浏览型号CD4066BM96E4的Datasheet PDF文件第3页浏览型号CD4066BM96E4的Datasheet PDF文件第4页浏览型号CD4066BM96E4的Datasheet PDF文件第5页浏览型号CD4066BM96E4的Datasheet PDF文件第6页浏览型号CD4066BM96E4的Datasheet PDF文件第7页 
CD4066B  
CMOS QUAD BILATERAL SWITCH  
SCHS051D – NOVEMBER 1998 – REVISED SEPTEMBER 2003  
15-V Digital or 7.5-V Peak-to-Peak  
Switching  
Matched Control-Input to Signal-Output  
Capacitance: Reduces Output Signal  
Transients  
125-Typical On-State Resistance for 15-V  
Operation  
Frequency Response, Switch On = 40 MHz  
Typical  
Switch On-State Resistance Matched to  
Within 5 Over 15-V Signal-Input Range  
On-State Resistance Flat Over Full  
Peak-to-Peak Signal Range  
100% Tested for Quiescent Current at 20 V  
5-V, 10-V, and 15-V Parametric Ratings  
Meets All Requirements of JEDEC Tentative  
Standard No. 13-B, Standard Specifications  
for Description of “B” Series CMOS  
Devices  
High On/Off Output-Voltage Ratio: 80 dB  
Typical at f = 10 kHz, R = 1 kΩ  
is  
L
High Degree of Linearity: <0.5% Distortion  
Typical at f = 1 kHz, V = 5 V p-p,  
Applications:  
is  
is  
V
– V 10 V, R = 10 kΩ  
– Analog Signal Switching/Multiplexing:  
Signal Gating, Modulator, Squelch  
Control, Demodulator, Chopper,  
Commutating Switch  
DD  
SS  
L
Extremely Low Off-State Switch Leakage,  
Resulting in Very Low Offset Current and  
High Effective Off-State Resistance: 10 pA  
– Digital Signal Switching/Multiplexing  
– Transmission-Gate Logic Implementation  
– Analog-to-Digital and Digital-to-Analog  
Conversion  
– Digital Control of Frequency, Impedance,  
Phase, and Analog-Signal Gain  
Typical at V  
– V = 10 V, T = 25°C  
DD  
SS A  
Extremely High Control Input Impedance  
(Control Circuit Isolated From Signal  
12  
Circuit): 10 Typical  
Low Crosstalk Between Switches: –50 dB  
Typical at f = 8 MHz, R = 1 kΩ  
is  
L
E, F, M, NS, OR PW PACKAGE  
(TOP VIEW)  
1
2
3
4
5
6
7
14  
13  
12  
11  
SIG A IN/OUT  
SIG A OUT/IN  
SIG B OUT/IN  
SIG B IN/OUT  
CONTROL B  
CONTROL C  
V
DD  
CONTROL A  
CONTROL D  
SIG D IN/OUT  
10 SIG D OUT/IN  
9
8
SIG C OUT/IN  
SIG C IN/OUT  
V
SS  
description/ordering information  
The CD4066B is a quad bilateral switch intended for the transmission or multiplexing of analog or digital signals.  
It is pin-for-pin compatible with the CD4016B, but exhibits a much lower on-state resistance. In addition, the  
on-state resistance is relatively constant over the full signal-input range.  
The CD4066B consists of four bilateral switches, each with independent controls. Both the p and the n devices  
in a given switch are biased on or off simultaneously by the control signal. As shown in Figure 1, the well of the  
n-channel device on each switch is tied to either the input (when the switch is on) or to V (when the switch  
SS  
is off). This configuration eliminates the variation of the switch-transistor threshold voltage with input signal and,  
thus, keeps the on-state resistance low over the full operating-signal range.  
The advantages over single-channel switches include peak input-signal voltage swings equal to the full supply  
voltage and more constant on-state impedance over the input-signal range. However, for sample-and-hold  
applications, the CD4016B is recommended.  
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of  
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.  
Copyright 2003, Texas Instruments Incorporated  
PRODUCTION DATA information is current as of publication date.  
Products conform to specifications per the terms of Texas Instruments  
standard warranty. Production processing does not necessarily include  
testing of all parameters.  
1
POST OFFICE BOX 655303 DALLAS, TEXAS 75265  

CD4066BM96E4 替代型号

型号 品牌 替代类型 描述 数据表
CD4066BM96 TI

完全替代

CMOS QUAD BILATERAL SWITCH
CD4066BM TI

类似代替

CMOS QUAD BILATERAL SWITCH

与CD4066BM96E4相关器件

型号 品牌 获取价格 描述 数据表
CD4066BM96G4 TI

获取价格

CMOS QUAD BILATERAL SWITCH
CD4066BME4 TI

获取价格

CMOS QUAD BILATERAL SWITCH
CD4066BMG4 TI

获取价格

CMOS QUAD BILATERAL SWITCH
CD4066B-MIL TI

获取价格

CMOS 四路双向开关
CD4066BMJ NSC

获取价格

Quad Bilateral Switch
CD4066BMJ/883 TI

获取价格

QUAD 1-CHANNEL, SGL POLE SGL THROW SWITCH, CDIP14, CERAMIC, DIP-14
CD4066BMJ/883C ROCHESTER

获取价格

SPST
CD4066BMS INTERSIL

获取价格

CMOS 4-Bit Magnitude Comparator
CD4066BMT TI

获取价格

CMOS QUAD BILATERAL SWITCH
CD4066BMTE4 TI

获取价格

CMOS QUAD BILATERAL SWITCH