C2000RWSeries
Wide 2:1Input 20W
Single, Dual & Triple Output
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Conditions
12 VDC Input
Min.
9.0
Typ.
12.0
24.0
48.0
Max.
18.0
36.0
75.0
Units
Key Features:
Input Voltage Range
24 VDC Input 18.0
48 VDC Input 36.0
(Pi) Filter
VDC
• 20W Output Power
• 2:1 Input Voltage Range
• 1,600 VDC Isolation
• 12, 24, & 48V Input
• Single, Dual, Triple Output
• Remote ON/OFF
Input Filter
Output
Parameter
Output Voltage Accuracy
Line Regulation, Single, Dual Output
Conditions
Min.
Typ.
2.0
0.5
1.0
5.0
0.5
3.0
3.0
5.0
Max.
Units
%
%
For Vin Min to Max
Vout 1
Vout 2 & Vout 3
Iout = 10% to 100%
Line Regulation, Triple Output
%
• >550 kHour MTBF
Load Regulation, Single Output
Load Regulation, Dual Output
%
%
• Industry Standard Pin-Out
Iout = 10% to 100%
Iout = 10% to 100%, Vout 1
Iout = 10% to 100%, Vout 2 & Vout 3
Load Regulation, Triple Output
%
Ripple, See Note 1
Noise, See Note 1
Output Power Protection, See Note 2
Over Voltage Protection, See Note 3
Temperature Coefficient
Output Short Circuit
General
0.2% Vout + 20 mV P - P Max.
0.5% Vout + 50 mV P - P Max.
120
112
0.02
%
%
%/°C
165
Continuous (Autorecovery)
Parameter
Conditions
Min.
60 Seconds 1,600
500 VDC 1,000
100 kHz, 1V
Typ.
Max.
Units
VDC
M⍀
pF
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
Remote On/Off, See Note 4
Parameter
1,000
200
kHz
Conditions
Min.
5.0
Typ.
Max.
15.0
+1.0
-1
Units
VDC
VDC
mA
Supply On
Supply Off
-1.0
Input Current (On)
Input Current (Off)
Control Common
Environmental
Parameter
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
1
mA
Referenced to Negative Input (pin 2)
Conditions
Min.
Typ.
Max.
+70
+100
+105
Units
°C
°C
Ambient
Case
-25
-55
°C
See Derating Curve
RH, Non-condensing
Humidity
95
%
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Physical
Case Size
Case Material
Weight
Reliability Specifications
Parameter
MTBF
2.0 x 2.0 x 0.45 Inches (50.8 x 50.8 x 11.4 mm)
Nickel Coated Copper with Non-Conductive Base
2.47 Oz (70g)
Conditions
Min.
550
Typ.
Typ.
Max.
Units
kHours
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
MIL HDBK 217F, 25°C, Gnd Benign
Absolute Maximum Ratings
Parameter
Conditions
Min.
Max.
25.0
50.0
100.0
260
Units
VDC
°C
12 VDC Input -0.7
24 VDC Input -0.7
48 VDC Input -0.7
Input Voltage Surge (0.1 Sec)
Lead Temperature
1.5 mm From Case For 10 Sec
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com