5秒后页面跳转
捷配首页

Datasheet > BRR1A16E
BRR1A16E PDF预览

BRR1A16E

更新时间： 2024-01-21 21:52:56
品牌 Logo 应用领域
杰尔 - AGERE /
页数 文件大小 规格书
12页 222K
描述
Quad Differential Receivers BRF1A, BRF2A, BRS2B, BRR1A, and BRT1A

阅读下载

获取价格

BRR1A16E 技术参数

是否无铅： 含铅是否Rohs认证： 不符合
生命周期：Active零件包装代码：DIP
包装说明：PLASTIC, DIP-16针数：16
Reach Compliance Code：unknown风险等级：5.62
Is Samacsys：N输入特性：DIFFERENTIAL
接口集成电路类型：LINE RECEIVER接口标准：GENERAL PURPOSE
JESD-30 代码：R-PDIP-T16JESD-609代码：e0
湿度敏感等级：NOT SPECIFIED功能数量：4
端子数量：16最高工作温度：125 °C
最低工作温度：-40 °C封装主体材料：PLASTIC/EPOXY
封装代码：DIP封装形状：RECTANGULAR
封装形式：IN-LINE峰值回流温度（摄氏度）：NOT SPECIFIED
认证状态：COMMERCIAL最大接收延迟：4 ns
接收器位数：4座面最大高度：5.08 mm
最大供电电压：5.5 V最小供电电压：4.5 V
标称供电电压：5 V表面贴装：NO
技术：BICMOS温度等级：AUTOMOTIVE
端子面层：TIN LEAD端子形式：THROUGH-HOLE
端子节距：2.54 mm端子位置：DUAL
处于峰值回流温度下的最长时间：NOT SPECIFIED宽度：7.62 mm
Base Number Matches：1

BRR1A16E 数据手册

 浏览型号BRR1A16E的Datasheet PDF文件第2页浏览型号BRR1A16E的Datasheet PDF文件第3页浏览型号BRR1A16E的Datasheet PDF文件第4页浏览型号BRR1A16E的Datasheet PDF文件第5页浏览型号BRR1A16E的Datasheet PDF文件第6页浏览型号BRR1A16E的Datasheet PDF文件第7页 
Data Sheet  
April 2001  
Quad Differential Receivers  
BRF1A, BRF2A, BRS2B, BRR1A, and BRT1A  
The BRF1A device is the generic receiver in this  
family and requires the user to supply external  
Features  
resistors on the circuit board for impedance  
matching.  
■ Pin equivalent to the general-trade 26LS32 device,  
with improved speed, reduced power consumption,  
and significantly lower levels of EMI  
The BRF2A is identical to the BRF1A, but has an  
electrostatic discharge (ESD) protection circuit  
added to significantly improve the ESD human-body  
model (HBM) characteristics on the differential input  
terminals.  
■ High input impedance approximately 8 kΩ  
■ Four line receivers per package  
■ 400 Mbits/s maximum data rate when used with  
Agere Systems Inc. data transmission drivers  
The BRS2B is identical to the BRF2A, but has a  
preferred state feature that places the output in the  
high state when the inputs are open, shorted to  
ground, or shorted to the power supply.  
■ Meets enhanced small device interface (ESDI)  
standards  
■ 4.0 ns maximum propagation delay  
■ <0.20 V input sensitivity  
The BRR1A is equivalent to the BRF1A, but has a  
110 Ω resistor connected across the differential  
inputs. This eliminates the need for an external  
resistor when terminating a 100 Ω impedance line.  
This device is designed to work with the DP1A or  
PNPA in point-to-point applications.  
■ −1.2 V to +7.2 V common-mode range  
■ −40 °C to +125 °C ambient operating temperature  
range (wider than the 41 Series)  
■ Single 5.0 V ± 10% supply  
The BRT1A is equivalent to the BRF1A; however, it  
is provided with a Y-type resistor network across the  
differential inputs and terminated to ground. The  
Y-type termination provides the best EMI results.  
This device is not recommended for applications  
where the differences in ground voltage between the  
driver and the receiver exceed 1 V. This device is  
designed to work with the DG1A or PNGA in point-to-  
point applications.  
■ Output defaults to logic 1 when inputs are left  
open*  
■ Available in four package types  
■ Lower power requirement than the 41 Series  
Description  
The powerdown loading characteristics of the  
receiver input circuit are approximately 8 kΩ relative  
to the power supplies; hence, they will not load the  
transmission line when the circuit is powered down.  
For those circuits with termination resistors, the line  
will remain impedance matched when the circuit is  
powered down.  
These quad differential receivers accept digital data  
over balanced transmission lines. They translate  
differential input logic levels to TTL output logic  
levels. All devices in this family have four receivers  
with a common enable control. These receivers are  
pin equivalent to the general-trade 26LS32, but offer  
increased speed and decreased power consumption.  
They replace the Agere 41 Series receivers.  
The packaging options that are available for these  
quad differential line drivers include a 16-pin DIP; a  
16-pin, J-lead SOJ; a 16-pin, gull-wing small-outline  
integrated circuit (SOIC); and a 16-pin, narrow-body,  
gull-wing SOIC.  
* This feature is available on BRF1A and BRF2A.  
1234567...12

下载PDF

与BRR1A16E相关器件

型号 品牌 描述 获取价格 数据表
BRR1A16E-TR AGERE Quad Differential Receivers BRF1A, BRF2A, BRS2B, BRR1A, and BRT1A

获取价格
BRR1A16G AGERE Quad Differential Receivers BRF1A, BRF2A, BRS2B, BRR1A, and BRT1A

获取价格
BRR1A16G-TR AGERE Quad Differential Receivers BRF1A, BRF2A, BRS2B, BRR1A, and BRT1A

获取价格
BRR1A16NB AGERE Quad Differential Receivers BRF1A, BRF2A, BRS2B, BRR1A, and BRT1A

获取价格
BRR1A16NB-TR AGERE Quad Differential Receivers BRF1A, BRF2A, BRS2B, BRR1A, and BRT1A

获取价格
BRR1A16P AGERE Quad Differential Receivers BRF1A, BRF2A, BRS2B, BRR1A, and BRT1A

获取价格

与BRR1A16E相关文章

您还可以找


热门产品
PCB打样/小批量
铝基板
BOM智能配单
PCBA制造
钣金
精密CNC
模具注塑
薄膜开关
精选活动
PCBA打样特惠
四六层板品质升级
铝基板品质升级
一体化电子制造
DFM下载
服务支持
企业认证
产品展示
工厂展示
工艺能力
积分商城
关于捷配
捷配简介
企业文化
公司动态
人才招聘
联系我们
帮助中心
下单流程
付款流程
开票流程
常见问题
全球PCB制造服务专线 400-613-0088

工作时间：9:00-21:00

CEO邮箱：ceo@jiepei.com

投诉邮箱：tousu@jiepei.com

捷配网-微信公众号 微信公众号
捷配网-微信公众号 抖音公众号
资质认证：
合作快递：
支付方式：
Copyright © 2024 Jiepei.com Inc. All Rights Reserved. 版权所有:杭州捷配信息科技有限公司 浙公网安备 33010502006866号 浙ICP备10014259号-119 营业执照ICP证