5秒后页面跳转
捷配首页

Datasheet > 电源电路 > 电源管理电路> BQ76925PWR
BQ76925PWR PDF预览

BQ76925PWR

更新时间： 2024-02-24 05:56:27
品牌 Logo 应用领域
德州仪器 - TI 电池
页数 文件大小 规格书
35页 1110K
描述
Host Controlled Analog Front End for 3-Series to 6-Series Cell Li-Ion/Li-Polymer Battery

阅读下载

获取价格

BQ76925PWR 技术参数

是否无铅： 不含铅是否Rohs认证： 符合
生命周期：Active零件包装代码：QFN
包装说明：HVQCCN, LCC24,.16SQ,20针数：24
Reach Compliance Code：compliantECCN代码：EAR99
HTS代码：8542.39.00.01Factory Lead Time：1 week
风险等级：1.62可调阈值：YES
模拟集成电路 - 其他类型：POWER SUPPLY SUPPORT CIRCUITJESD-30 代码：S-PQCC-N24
JESD-609代码：e4长度：4 mm
湿度敏感等级：2信道数量：1
功能数量：1端子数量：24
最高工作温度：85 °C最低工作温度：-25 °C
封装主体材料：PLASTIC/EPOXY封装代码：HVQCCN
封装等效代码：LCC24,.16SQ,20封装形状：SQUARE
封装形式：CHIP CARRIER, HEAT SINK/SLUG, VERY THIN PROFILE峰值回流温度（摄氏度）：260
电源：4.2/26.4 V认证状态：Not Qualified
座面最大高度：1 mm子类别：Power Management Circuits
最大供电电流 (Isup)：0.048 mA最大供电电压 (Vsup)：26.4 V
最小供电电压 (Vsup)：4.2 V标称供电电压 (Vsup)：21.6 V
表面贴装：YES温度等级：OTHER
端子面层：Nickel/Palladium/Gold (Ni/Pd/Au)端子形式：NO LEAD
端子节距：0.5 mm端子位置：QUAD
处于峰值回流温度下的最长时间：NOT SPECIFIED宽度：4 mm
Base Number Matches：1

BQ76925PWR 数据手册

 浏览型号BQ76925PWR的Datasheet PDF文件第2页浏览型号BQ76925PWR的Datasheet PDF文件第3页浏览型号BQ76925PWR的Datasheet PDF文件第4页浏览型号BQ76925PWR的Datasheet PDF文件第5页浏览型号BQ76925PWR的Datasheet PDF文件第6页浏览型号BQ76925PWR的Datasheet PDF文件第7页 
bq76925  
www.ti.com  
SLUSAM9B –JULY 2011–REVISED DECEMBER 2011  
Host Controlled Analog Front End for 3-Series to 6-Series Cell Li-Ion/Li-Polymer Battery  
Protection and Gas Gauging Applications  
Check for Samples: bq76925  
1
FEATURES  
DESCRIPTION  
The bq76925 Host controlled analog front end (AFE)  
is part of a complete pack monitoring, balancing and  
protection system for 3-, 4-, 5-, or 6-series cell Li-Ion  
and Li-Polymer batteries. The bq76925 allows a Host  
controller to easily monitor individual cell voltages,  
pack current and temperature. This information may  
be used by the Host to determine unsafe or faulty  
•
Analog Interface for Host cell Measurement  
–
–
Cell Input MUX, Level Shifter, and Scaler  
1.5-/ 3.0-V Low-Drift, Calibrated Reference  
Allows Accurate Analog to Digital  
Conversions  
•
Analog Interface for Host Current  
Measurement  
operating  
conditions  
such  
as  
overvoltage,  
undervoltage, over-temperature and overcurrent, as  
well as cell imbalance, state of charge and state of  
health conditions.  
–
Variable Gain Current Sense Amplifier  
Capable of Operation with 1-mΩ Sense  
Resistor  
Cell input voltages are level-shifted, multiplexed,  
scaled, and output for measurement by a Host ADC.  
A low-drift calibrated reference voltage is provided on  
a dedicated pin to enable accurate measurements.  
•
•
Switchable Thermistor Bias output for Host  
Temperature Measurements  
Overcurrent Comparator with Dynamically  
Adjustable Threshold  
The voltage across an external sense resistor is  
amplified and output to a Host ADC for both charge  
and discharge current measurements. Two gain  
settings enable operation with a variety of sense  
resistor values over a wide range of pack currents.  
–
–
Alerts Host to Potential Overcurrent Faults  
May be used to Wake up Host on Load  
Connect  
•
Integrated Cell Balancing FETs  
To enable temperature measurements by the Host,  
the AFE provides a separate output pin for biasing an  
external thermistor network. This output can be  
switched on and off under Host control to minimize  
power consumption.  
–
–
Individual Host Control  
50 mA per-cell Balancing Current  
•
•
Supports Cell Sense-line Open Wire Detection  
Integrated 3.3-V Regulator for Powering  
Micro-controller and/or LEDs  
I2C Interface for Host Communications  
The bq76925 includes  
a
comparator with  
a
dynamically selectable threshold for monitoring  
current. The comparator result is driven through an  
open-drain output to alert the host when the threshold  
is exceeded. This feature can be used to wake up the  
Host on connection of the load, or to alert the Host to  
a potential fault condition.  
•
–
Optional Packet CRC for Robust Operation  
•
•
Supply Voltage Range From 4.2 to 26.4 V  
Low Power Consumption  
–
–
40 µA Typical in Normal Mode  
1.5 µA Maximum in Sleep Mode  
The bq76925 integrates cell balancing FETs that are  
fully controlled by the Host. The balancing current is  
set by external resistors up to a maximum value of 50  
mA. These same FETs may be utilized in conjunction  
with cell voltage measurements to detect an open  
wire on a cell sense-line.  
•
20-pin TSSOP or 24-pin QFN Package  
APPLICATIONS  
•
Primary Protection in Li-Ion Battery Packs  
The Host communicates with the AFE via an I2C  
interface. A packet CRC may optionally be used to  
ensure robust operation. The device may be put into  
a low-current sleep mode via the I2C interface and  
awakened by pulling up the ALERT pin.  
–
–
Cordless Power Tools  
Light Electric Vehicles (E-Bike, Scooter,  
etc.)  
–
–
–
UPS Systems  
Medical Equipment  
Portable Test Equipment  
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas  
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.  
PRODUCTION DATA information is current as of publication date.  
Products conform to specifications per the terms of the Texas  
Instruments standard warranty. Production processing does not  
necessarily include testing of all parameters.  
Copyright © 2011, Texas Instruments Incorporated  
1234567...35

下载PDF

与BQ76925PWR相关器件

型号 品牌 描述 获取价格 数据表
BQ76925RGE TI Host Controlled Analog Front End for 3 to 6 Series Cell Lithium-Ion/ Polymer Battery

获取价格
BQ76925RGER TI Host Controlled Analog Front End for 3-Series to 6-Series Cell Li-Ion/Li-Polymer Battery

获取价格
BQ76925RGET TI Host Controlled Analog Front End for 3-Series to 6-Series Cell Li-Ion/Li-Polymer Battery

获取价格
BQ76930 TI 串联电池监控系列 用于锂离子和磷酸盐电池应用

获取价格
BQ7693000DBT TI 6 至 10 节电池锂离子和锂磷酸盐电池监视器（bq76940 系列） | DBT | 3

获取价格
BQ7693000DBTR TI 6 至 10 节电池锂离子和锂磷酸盐电池监视器（bq76940 系列） | DBT | 3

获取价格

与BQ76925PWR相关文章

您还可以找


热门产品
PCB打样/小批量
铝基板
BOM智能配单
PCBA制造
钣金
精密CNC
模具注塑
薄膜开关
精选活动
PCBA打样特惠
四六层板品质升级
铝基板品质升级
一体化电子制造
DFM下载
服务支持
企业认证
产品展示
工厂展示
工艺能力
积分商城
关于捷配
捷配简介
企业文化
公司动态
人才招聘
联系我们
帮助中心
下单流程
付款流程
开票流程
常见问题
全球PCB制造服务专线 400-613-0088

工作时间：9:00-21:00

CEO邮箱：ceo@jiepei.com

投诉邮箱：tousu@jiepei.com

捷配网-微信公众号 微信公众号
捷配网-微信公众号 抖音公众号
资质认证：
合作快递：
支付方式：
Copyright © 2024 Jiepei.com Inc. All Rights Reserved. 版权所有:杭州捷配信息科技有限公司 浙公网安备 33010502006866号 浙ICP备10014259号-119 营业执照ICP证