bq24153A, bq24156A
bq24158, bq24159
www.ti.com
SLUSAB0A –OCTOBER 2010–REVISED FEBRUARY 2012
Fully Integrated Switch-Mode One-Cell Li-Ion Charger
With Full USB Compliance and USB-OTG Support
Check for Samples: bq24153A, bq24156A, bq24158, bq24159
1
FEATURES
23
•
Charge Faster than Linear Chargers
•
Synchronous Fixed-Frequency PWM
Controller Operating at 3 MHz With 0% to
99.5% Duty Cycle
•
High-Accuracy Voltage and Current Regulation
–
–
–
Input Current Regulation Accuracy: ±5%
(100 mA and 500 mA)
•
•
Automatic High Impedance Mode for Low
Power Consumption
Charge Voltage Regulation Accuracy:
±0.5% (25°C), ±1% (0°C to 125°C)
Robust Protection
–
Reverse Leakage Protection Prevents
Battery Drainage
Charge Current Regulation Accuracy: ±5%
•
Input Voltage Based Dynamic Power
Management (VIN DPM)
–
–
Thermal Regulation and Protection
Input/Output Overvoltage Protection
•
•
Bad Adaptor Detection and Rejection
•
•
•
•
•
Status Output for Charging and Faults
USB Friendly Boot-Up Sequence
Automatic Charging
Safety Limit Register for Maximum Charge
Voltage and Current Limiting
•
High-Efficiency Mini-USB/AC Battery Charger
for Single-Cell Li-Ion and Li-Polymer Battery
Packs
Power Up System without Battery bq24158/9
Boost Mode Operation for USB OTG:
(bq24153A/8 only)
•
•
20-V Absolute Maximum Input Voltage Rating
9-V Maximum Operating Input
Voltage-bq24156A/9
–
Input Voltage Range (from Battery): 2.5 V to
4.5 V
•
6-V Maximum Operating Input
Voltage-bq24153A/8
–
Output for VBUS: 5.05 V/ 200 mA
•
2.1 mm x 2 mm 20-Pin WCSP Package
•
•
Built-In Input Current Sensing and Limiting
Integrated Power FETs for Up To 1.5-A Charge
Rate-bq24156A/9, 1.25A-bq24153A/8
APPLICATIONS
•
•
•
Mobile and Smart Phones
MP3 Players
•
Programmable Charge Parameters through
I2C™ Compatible Interface (up to 3.4 Mbps):
Handheld Devices
–
–
–
–
–
–
–
Input Current Limit
Figure 1. Typical Application Circuit
VIN DPM Threshold
V
L
1 µH
Fast-Charge/Termination Current
Charge Regulation Voltage (3.5 V to 4.44 V)
Low Charge Current Mode Enable/Disable
Safety Timer with Reset Control
Termination Enable/Disable
SNS
O
V
BAT
V
VBUS
BUS
SW
U1
bq24153A/8
C
C
O1
22 µF
IN
1 µF
C
C
O2
BOOT
10 nF
33 µF
PMID
BOOT
PGND
C
IN
PACK+
C
4.7
µF
SIN
VAUX
10 kΩ
+
0.1 µF
CSIN
10 kΩ
10 kΩ
SCL
SCL
SDA
STAT
OTG
CSOUT
PACK–
SDA
STAT
OTG
C
SOUT
C
VREF
VREF
0.1 µF
CD
10 kΩ
CD
1 µF
10 kΩ
HOST
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
3
NanoFree is a trademark of Texas Instruments.
I2C is a trademark of NXP B.V. Corporation.
UNLESS OTHERWISE NOTED this document contains
PRODUCTION DATA information current as of publication date.
Products conform to specifications per the terms of Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2010–2012, Texas Instruments Incorporated