Data Sheet
100VAC Input/2.5V-12V (250-360mA) Output
Isolated High-power LED Driver for Illumination
BP5844
Absolute Maximum Ratings
Dimensions (Unit : mm)
33.5MAX.
15.1MAX.
Parameter
Symbol
Limits
170
Units
V
Input voltage
Vi
Vo
Output voltage (limits)
12
V
Output voltage (no load)
Output current
Vo
12.5
V
MARKING SIDE
Io
378
mA
V
Output control terminal voltage
Withstand voltage
VCTL
BV
12.5
1.8
kV
°C
°C
°C
Maximum surface temperature
Operating temperature range
Storage temperature range
Tcmax
Topr
Tstg
105
1
3
4
5
8
9 10 11
-20 to +80
-25 to +85
0.5 0.1
0.75 0.1
1.3 0.2
2.54 0.2
3.9MAX
2.54�10=25.4TYP.
4.4MAX.
10.7MAX.
Electrical Characteristics
Spec
Typ.
141
360
-
Parameter
Symbol
Units
Conditions
Min.
Max.
170
378
12
0.5
-
Input voltage range
Output current
Output voltage range
Output ripple voltage
Conversion efficiency
Vi
Io
Vo
Vp
η
-
113
342
2.5
-
V
mA
V
Vp-p
%
Derating Curve
∗1
∗2
Vi=141V,R1=0.78Ω
Vi=141V,Io=360mA
Vi=141V,Io=360mA
Vi=141V,Vo=12V,Io=360mA
Derating Curve
5
4
3
2
1
-
85
80
∗1 Maximum output current varies depending on ambient temperature. Refer to the derating curve.
Operation Range
∗2 Spike noise is not included in output ripple voltage.
Application Circuit Example
0
Pin No.
Terminal name
Input terminal (+)
-30 -20 -10
0 10 20 30 40 50 60 70 80 90
BP5844
1
2
3
Ambient Temperature Ta(°C)
Skip
Input terminal (-)
4,5 N.C
6-7 Skip
Output capacitor connection terminal (-)
LED connection terminal (cathode)
10 LED connection terminal (anode)
11 VCTL terminal
1
3
8
9 10 11
Use a fuse for safety.
Output control
terminal
F1
Output Characteristics
R1
8
9
AC100V
ZNR1
D1
CONVERSION EFFICIENCY
LF1
(Vi=141V, R1=0.78Ω, Ta=25°C)
+
C1
100
90
80
70
60
50
40
30
20
10
0
C3
C4
C5
Please verify operation and characteristics in the customer's circuit before actual usage.
Ensure that the load current does not exceed the maximum rating.
Operation Range
External Component Specifications
C1 : Input capacitor
C2 : Output capacitor
R1 : Output current setting resistor
10µF / 250V (general purpose)
47µF / 25V low impedance type
0.00
2.00
4.00
6.00
8.00 10.00 12.00 14.00
Output Voltage Vo[V]
0.78Ω(0.22Ω+0.56Ω)±1% 1/4 (Io=360mA)
By changing R1 it is possible to adjust output voltage.
Refer the Output Voltage Setting graph at right
Use if required
adove 125V 0.1 to 0.22µF
2200pF(Products with basic isolation certification)
400V / 1A
Use a fuse for safety.
10mH
A varistor is required to protect against lightning surges
and static electricity.
Load Regulation
C3,C4: Noise reduction capacitor
LOAD REGULATION
(Vi=141V, R1=0.78Ω, Ta=25°C)
C5: Noise reduction capacitor
D1: Diode bridge
F1: FUSE
LF1: Line filter
ZNR1: Varistor
14.0
12.0
10.0
8.0
Operation Range
6.0
4.0
2.0
0.0
PWM dimming circuit
0
100
200
300
400
500
600
BP5844
Output Current Io[mA]
VoH 9V PWM dimming by
using the 11pin
1
3
8
9
10 11
3 Terminal Reg(5V)
VF X n 9V
F1
IN OUT
COM
Micro
computer
Output voltage setting
R1
D1
AC100V
Output current-Setting resistor characteristic
LF1
10kΩ
+
C2
+
C1
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
ZNR1
C3
C4
C5
PWM signal
Phase control dimming circuit
PWM dimming is possible by configuring a phase control circuit at the input side.
0.0
Spec
Min. Typ. Max.
6.5 6.9 7.3
PWM dimming signal
In case of using PWM or phase
control dimming, please input the
PWM signals at the VCTL pin.
0.24 0.26 0.28 0.30 0.32 0.34 0.36 0.38
Parameter
Symbol
Units Conditions
Output Current(A)
LED OFF Voltage
PWM Signal H level
PWM Signal L level
VoL
VCTL(H)
VCTL(L)
V
V
V
VoH 9V
How to calculate setting resistor R1
R1=0.13741/(0.91 x lo-0.151)
lo : Output current
3
0
5
-
10
0.5
PWM Signal freqency fosc
∗3 Flickering may occur due to LED load. Please evaluate with the actual application to determine the frequency.
90 100 132 kHz ∗3
Note) A maximum output current is set to 360mA.
Operation beyond this limit are prohibited.
www.rohm.com
©2010 ROHM Co., Ltd. All rights reserved.
2010.01 - Rev.A
1/1