Applicable standard
Operating
Storage
-40 °C to +105 °C ( 95 %RH Max.)
-40 °C to +85 °C ( 95 %RH Max.)
temperature range
temperature range
Characteristic
impedance
Applicable
cable
- W
-
75 Ω( 0 to 12 GHz)
Rating Power
-
Peculiarity
SPECIFICATIONS
ITEM
TEST METHOD
REQUIREMENTS
According to drawing.
QT AT
CONSTRUCTION
General examination
Marking
Visually and by measuring instrument.
Confirmed visually.
X
-
X
-
ELECTRICAL CHARACTERISTICS
Contact resistance
100 mA Max.(DC or 1000 Hz)
Center contact 53 mΩ Max.
X
X
X
X
X
X
X
X
Outer contact 23 mΩ Max.
500 MΩ Min.
Insulation resistance
Withstanding voltage
Voltage standing wave
ratio (Return loss)
Insertion loss
100 V DC.
200 V AC for 1 min. current leakage 2 mA Max.
Frequency 0 to 3 GHz.
Frequency 3 to 12 GHz.
Frequency - to - GHz.
No breakdown.
VSWR 1.3 Max. (R.L. 17.7 dB Min.)
VSWR 1.5 Max. (R.L. 13.9 dB Min.)
- dB Max.
X
-
-
-
MECHANICAL CHARACTERISTICS
-0
1.32
by steel gauge. (BNC)
Contact insertion and
extraction forces
Insertion and
φ
Insertion force
Extraction force 0.6 N Min.
Insertion force 40 N Max.
- N Max.
-
X
X
-
X
-
-0.005
Measured by applicable connector. (D.FL75)
extraction forces
1
Extraction force 9 N Min. (First time)
X
-
3 N Min. ( 2 to 20 times)
Mechanical operation
500 times insertion and extractions. (BNC)
20 times insertion and extractions. (D.FL75)
1)Contact resistance:
Center contact 62 mΩ Max.
Outer contact 32 mΩ Max.
2)No damage, crack and looseness of parts.
X
-
Vibration
Shock
Frequency 10 to 500 Hz single amplitude 0.75 mm, 1)No electrical discontinuity of 1 μs.
X
X
-
-
98 m/s2 at 10 cycles for 3 directions.
490 m/s2 directions of pulse 11 ms
at 3 times for 3 directions.
2)No damage, crack and looseness of parts.
Cable clamp strength
(Against cable pull)
Using a pulling tester, pull the cable axially at a rate
of - mm/min. and record the strength at which
the cable or connector breaks.
- N Min.
-
-
ENVIRONMENTAL CHARACTERISTICS
Damp heat
Exposed at +40 °C, 90 to 95 %
total 96 h.
1)Insulation resistance: 100 MΩ Min.
(at high humidity)
2) Insulation resistance: 1000 MΩ Min.
(at dry)
X
-
3)No damage, crack and looseness of parts.
No damage, crack and looseness of parts.
Rapid change of
temperature
Temperature
Time
-40 → - → +105 →
- °C
X
X
-
-
30 → 3 →
30 →
3 min.
Under 5 cycles.
Exposed in 5 % salt water spray for 48 h.
Corrosion salt mist
Satisfy the V.S.W.R. (R.L.) standard.
Count
0
Description of revisions
Designed
Checked
Date
NK.NINOMIYA
NK.NINOMIYA
NK.OOSAWA
NK.OOSAWA
20230620
20230620
20230620
20230620
Remark
Note
Approved
Checked
Designed
Drawn
1
This standard shall apply if it differs from the standard on the plug side.
Unless otherwise specified, refer to IEC 60512.
Note QT:Qualification Test AT:Assurance Test X:Applicable Test
Drawing No.
Part No.
ELC-401043-00-00
SPECIFICATION SHEET
BNC(75)J-D.FL75J-BPA-2
0
1/1
HIROSE ELECTRIC CO., LTD.
Code No.
CL0311-0039-0-00
FORM HD0011-2-1