Storage temperature
range
(before unpacking)
Storage temperature
range (after mounting,
but not operating)
-40 to +85 [deg. C] (85%RH MAX)
No freezing and condensing
-10 to +60 [deg. C] (40 to 75%RH)
-10 to +60 [deg. C] (85%RH MAX)
No freezing and condensing
Operating temperature
range
Characteristic
impedance
Operating
condition
Differential 100 [ohm]
1.0 to 3.6V
ACTIVATE voltage
Input signal IF
SLVS-200
Input signal voltage
Suitable connector
Differential voltage 200 to 1400 mVp Input power voltage
(BF4-IR2) BF4-IR2-16P-0.5SH,
3.0 to 3.6V (typ 3.3V)
SPECIFICATIONS
TEST METHOD
ITEM
REQUIREMENTS
QT AT
CONSTRUCTION
Dimension, Construction Check visually and measure dimension with dimension
According to the drawing
X
X
X
X
and Finishing
measurement instrument.
Marking
Check visually.
ELECTRIC CHARACTERISTICS
Data rate performance
Measure eye diagram when input differential 200mVp
No mask hit at 0.05 to 6.25 Gbps
(The mask should be similar to standard
ethernet mask)
X
-
signal.
Measure eye diagram input 6.25Gbps PRBS7 differential
200mVp signal.
No mask hit (The mask should be
similar to standard ethernet mask)
OE-SDn voltage -0.3 to 1.0V
X
X
X
X
Signal detect (OE-SDn)
ACT detect ( EO-ACTn)
Shall be turned OE-SDn=Low when EO-ACT=High and
VDD=3.3V. (Same measurement method as “Data rate”)
Shall be turned EO-ACTn=Low when TX is during
VDD=3.3V.
X
X
X
-
EO-ACTn voltage -0.3 to 1.0V
< 1 X 10-12
Bit error rate (BER)
Measure BER with BERT during input differential 6.25Gbps
PRBS7 200mVp signal.
Power consumption
Output signal voltage
Measure current by digital multimeter during operating
condition at VDD=3.3V.
X
X
-
≦160mW
Shall be checked by eye diagram when input 6.25Gbps
PRBS7 differential 200mVp signal.
X
160 to 330mVp
OPTICAL CHARACTERISTICS
LED light emission
Apply V=3.0 to 3.6V at the pin, then check if LED light is
Green light shall be visible
Amber light shall be visible
X
X
X
X
(Green)
visible or not.
LED light emission
(Amber)
Apply V=3.0 to 3.6V at the pin, then check if LED light is
visible or not.
MECHANICAL CHARACTERISTICS
Mating Durability
(BF4-IR2) 1000 cycles of mating and unmating with BF4-IR2 No looseness, breakage and cracks
-
X
(Visual and data transmission check
before and after test)
socket.
-
-
X
X
Vibration
Vibration for 2 hours in 3 directions, at an amplitude of 1.5mm
with the frequency range 10 to 55 [Hz].
3 times and 3 directions with the acceleration
490 [m/s2] in duration 11ms.
Shock
-
-
X
X
> 10N
Fiber clamping strength
Loading tensile force to the fiber until break for same direction
with fiber exit.
COUNT
DESCRIPTION OF REVISIONS
DESIGNED
CHECKED
DATE
△
0
0
REMARK
APPROVED
CHECKED
DESIGNED
DRAWN
YY.HIYAMA
TS.YAMAZAKI
SK.AOYAMA
SK.AOYAMA
20221212
20221208
20221206
20221206
Each test item shall be checked by mating with suitable receptacle connector on
evaluation board (BF4-IR2)
This specifications sheet is based on using BF4MC type in BF4-IR2.
Note QT:Qualification Test, AT:Assurance Test
DRAWING NO.
ELC-391951-00-00
BF4-IR2IR2-01-2M
PART NO.
CODE NO.
SPECIFICATION SHEET
0
△
1/2
HIROSE ELECTRIC CO., LTD.
CL0831-1274-0-00
FORM HD0011-2-1