Datasheet
For Automotive 700 mA Adjustable Output
LDO Regulator
BD800M7WFP2-C
General Description
Key Specifications
The BD800M7WFP2-C is a linear regulator designed as a
low current consumption product for power supplies in
various automotive applications.
◼ Wide Temperature Range (Tj):
◼ Wide Operating Input Range:
◼ Low Current Consumption:
◼ Output Current Capability:
◼ High Output Voltage Accuracy:
◼ Output Voltage:
-40 °C to +150 °C
3 V to 42 V
17 μA(Typ)
700 mA
This product is designed for up to 45 V as an absolute
maximum voltage and to operate until 700 mA for the
output current with low current consumption 17 μA (Typ).
This can regulate the output with a very high accuracy(Note
1), ±2.6 %. The output voltage can be adjusted between 1.2
V and 16 V by an external resistive divider connected to
the adjustment pin. This regulator is therefore an ideal for
any applications requiring a direct connection to the battery
and a low current consumption.
±2.6 %
1.2 V to 16 V
Package
TO263-5
W(Typ) x D(Typ) x H(Max)
10.16 mm × 15.10 mm × 4.70 mm
A logical “HIGH” at the EN pin turns on the device, and in
the other side, the device is controlled to disable by a
logical “LOW” input to the EN pin.
The device features the integrated Over Current Protection
to protect the device from a damage caused by a short-
circuiting or an overload. This product also integrates
Thermal Shutdown Protection to avoid the damage by
overheating.
Furthermore, low ESR ceramic capacitors are sufficiently
applicable for the phase compensation.
(Note 1) The tolerance of feedback resistor is not included.
Features
◼ AEC-Q100 Qualified(Note 2)
◼ Output Shutdown Function (EN Function)
◼ Over Current Protection (OCP)
◼ Thermal Shutdown Protection (TSD)
(Note 2) Grade 1
Applications
◼ Power Train
◼ Body
◼ Audio System
◼ Navigation System
FIN
Typical Application Circuit
BD800M7WFP2-C
◼ Components Externally Connected
Capacitor: 0.1 µF ≤ CIN (Min), 1.47 µF ≤ COUT (Min) (Note 3)
Resistor: 5 kΩ ≤ R1 ≤ 200 kΩ (Note 4) (Note 5)
VADJ (Typ): 0.65 V
2:EN
4:ADJ
1:VIN 3:GND 5:VOUT
푉푂푈푇
푅2 = 푅1 (
− ꢀ)
Input
Voltage
Output
푉
퐴퐷퐽
R2
Voltage
(Note 6)
CADJ
COUT
Enable
Voltage
R1
CIN
(Note 3) Electrolytic, tantalum and ceramic capacitors can be used.
(Note 4) The tolerance of feedback resistor is not included in the accuracy of output voltage.
(Note 5) The value of a feedback resistor R1 must be within this range.
R2 value is defined by following the formula using the limitation of R1.
(Note 6) If it needs better transient characteristic, insert a capacitor between
the VOUT and ADJ pins. Refer to Typical Application and Layout Example for the details such as equations.
〇Product structure : Silicon integrated circuit 〇This product has no designed protection against radioactive rays.
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 14 • 001
TSZ02201-0GQG3A600020-1-2
1/36
22.Mar.2021 Rev.002