B1000RW Series
Coomppacctt 11 xx 22 IInnchh 10WW
Widdee IInnppuutt RRaannggee
DCC//DDCC CCoonnveerrtteerrss
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Conditions
12 VDC Input
Min.
8.0
Typ.
8.5
Max.
9.0
Units
Key Features:
● 10W Output Power
● UL Approved (File E245422)
● 2:1 Input Voltage Range
● 1,500 VDC Isolation
Input Start Voltage
24 VDC Input 15.0
48 VDC Input 30.0
π (Pi) Filter (Complies with EN55022 Class “A”)
17.0
33.0
18.0
36.0
VDC
Input Filter
Reverse Polarity Input Current
Short Circuit Input Power
2.0
A
mW
3,500 4,500
● Meets EN55022 Class “A” Output
Parameter
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Load Regulation
Ripple & Noise (20 MHz) (Note 1)
Ripple & Noise (20 MHz)
Ripple & Noise (20 MHz)
Output Power Protection
Transient Recovery Time (Note 2)
Transient Response Deviation
Temperature Coefficient
Output Short Circuit
General
Conditions
Min.
Typ.
±0.5
±0.5
±0.1
±0.1
50
Max.
±1.0
±1.0
±0.3
±0.5
75
Units
%
%
%
%
mV P - P
mV P - P
mV rms
%
μSec
%
● Compact 1 x 2 Inch Case
● Single & Dual Outputs
Dual Output , Balanced Loads
Vin = Min to Max
● Industry Standard Pin-Out
Iout = 10% to 100%
Over Line, Load & Temp.
25% Load Step Change
100
15
120
150
±2.0
±0.01 ±0.02
300
±4.0
%/°C
Continuous
Parameter
Isolation Voltage
Conditions
Min.
Typ.
Max.
Units
VDC
VDC
MΩ
pF
kHz
60 Seconds 1,500
Isolation Test Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
Environmental
Parameter
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
Flash Tested For 1 Sec 1,650
500 VDC 1,000
100 kHz, 1V
120
300
160
340
260
Conditions
Min.
-40
-40
-50
Typ.
+25
Max.
+71
+90
Units
°C
°C
Ambient
Case
+125
°C
Free Air Convection
RH, Non-condensing
Humidity
95
%
RFI
Six-Side Shielded Metal Case
EN55022 Class “A”
Conducted EMI
MicroPower Direct
232 Tosca Drive
Physical
Stoughton, MA 02072
USA
Case Size
Case Material
Weight
2.0 x 1.0 x 0.40 Inches (50.8 x 25.4 x 10.2 mm)
Metal with Non-Conductive Base (UL94-V0)
1.06 Oz (30g)
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Reliability Specifications
Parameter
MTBF
Conditions
Min.
Typ.
Max.
Units
MIL HDBK 217F, 25°C, Gnd Benign
700
kHours
Safety Standards
Safety Approvals
UL 1950, EN 60950, IEC 60950
UL, cUL; File No. E245422
Absolute Maximum Ratings
Parameter
Conditions
Min.
Typ.
Max.
25.0
50.0
100.0
260.0
5,000
Units
12 VDC Input -0.7
24 VDC Input -0.7
48 VDC Input -0.7
Input Voltage Surge (1 Sec)
VDC
Lead Temperature
Internal Power Dissipation
1.5 mm From Case For 10 Sec
All Models
°C
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.