CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Surface Mount
NPCAPTM-PXSSeries
Super low ESR, high ripple current capability
・
・
・
・
Longer life (20,000 hours at 105
)
℃
Rated voltage range : 4 to 16Vdc, Capacitance range : 39 to 560μF
Suitable for DC-DC converters, voltage regulators and decoupling applications
for computer motherboards etc.
Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
RoHS2 Compliant
Halogen Free
・
・
・
SPECIFICATIONS
◆
Items
Characteristics
Category
-55 to +105
4 to 16Vdc
℃
Temperature Range
Rated Voltage Range
Capacitance Tolerance
20% (M)
(at 20 , 120Hz)
℃
±
Leakage Current
I=0.2CV
*Note
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (Vdc
)
(at 20 after 2 minutes)
℃
Dissipation Factor
0.12 max.
(at 20 , 120Hz)
(tan
)
℃
δ
Low Temperature
Z(-25 )/Z(+20
)
)
1.15
1.25
℃
℃ ≦
Characteristics
Z(-55 )/Z(+20
℃
℃ ≦
(at 100kHz)
(Max. Impedance Ratio)
Endurance
The following specifications shall be satisfied when the capacitors are restored to 20 after the rated voltage is applied for 20,000 hours
℃
at 105
.
℃
Appearance
Capacitance change
No significant damage
20% of the initial value
≦±
D.F. (tan
ESR
Leakage current
)
150% of the initial specified value
150% of the initial specified value
The initial specified value
δ
≦
≦
≦
Bias Humidity
Surge Voltage
The following specifications shall be satisfied when the capacitors are restored to 20 after subjecting them to the DC rated voltage at
℃
60 , 90 to 95% RH for 1,000 hours.
℃
Appearance
Capacitance change
No significant damage
20% of the initial value
≦±
D.F. (tan
ESR
Leakage current
)
150% of the initial specified value
150% of the initial specified value
The initial specified value
δ
≦
≦
≦
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105 for 30 seconds
℃
through a protective resistor(R=1k )and discharge for 5 minutes 30 seconds.
Ω
Rated voltage (Vdc
Surge voltage (Vdc
)
)
4.0
4.6
6.3
7.2
10
12
16
18
Appearance
Capacitance change
No significant damage
20% of the initial value
≦±
D.F. (tan
ESR
Leakage current
)
150% of the initial specified value
150% of the initial specified value
The initial specified value
δ
≦
≦
≦
Soldering Heat
The following specifications shall be satisfied when the solder temperature is reduced back to 20 C to measure dip resistance after
°
soldering has been performed under the recommended soldering conditions.
Appearance
No significant damage
Capacitance value
Within the specified tolerance range
D.F. (tan
ESR
Leakage current
)
The initial specified value
The initial specified value
The initial specified value (Voltage treatment)
δ
≦
≦
≦
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
DIMENSIONS [mm]º
◆
MARKING
◆
EX) 6.3V390µF
●Terminal Code : A
W
S
69A
390
Size Code
F61
H70
L
A
B
C
W
P
φD
6.3V
6.3 5.8 6.6 6.6 7.2 0.5 to 0.8 1.9
8.0 6.7 8.3 8.3 9.0 0.7 to 1.1 3.1
0.3max.
A±0.2
L±0.3
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
CAT. No. E1001Y 2024