CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Surface Mount
NPCAPTM-PXDSeries
Super low ESR, impedance and high heat resistance have been obtained by using con-
ductive polymer as electrolyte.
For automobile modules and other high temperature applications
・
PXD
・
・
・
・
・
・
・
Endurance : 125 2,000 hours
℃
Rated voltage range : 2.5 to 10Vdc, Capacitance range : 47 to 470μF
Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
RoHS2 Compliant
Longer life
PXH
Halogen Free
AEC-Q200 compliant : Please contact Chemi-Con for more details, test data, information.
SPECIFICATIONS
◆
Items
Characteristics
Category
Temperature Range
-55 to +125
℃
Rated Voltage Range
Capacitance Tolerance
2.5 to 10Vdc
20% (M)
(at 20 , 120Hz)
±
℃
Leakage Current
Shall not exceed values shown in STANDARD RATINGS.
(at 20 after 2 minutes)
℃
*Note
Dissipation Factor
0.12 max.
(at 20 , 120Hz)
(tan
)
℃
δ
Low Temperature
Z(-25 )/Z(+20
)
)
1.15
1.25
℃
℃ ≦
Characteristics
Z(-55 )/Z(+20
℃
℃ ≦
(at 100kHz)
(Max. Impedance Ratio)
Endurance
The following specifications shall be satisfied when the capacitors are restored to 20 after the rated voltage is applied for 2,000 hours
℃
at 125
.
℃
Appearance
Capacitance change
No significant damage
20% of the initial value
≦±
D.F. (tan
ESR
Leakage current
)
200% of the initial specified value
200% of the initial specified value
The initial specified value
δ
≦
≦
≦
Bias Humidity
Surge Voltage
The following specifications shall be satisfied when the capacitors are restored to 20 after subjecting them to the DC rated voltage at
℃
60 , 90 to 95% RH for 1,000 hours.
℃
Appearance
Capacitance change
No significant damage
20% of the initial value
≦±
D.F. (tan
ESR
Leakage current
)
150% of the initial specified value
150% of the initial specified value
The initial specified value
δ
≦
≦
≦
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 125 for 30 seconds
℃
through a protective resistor(R=1k ) and discharge for 5 minutes 30 seconds.
Ω
Rated voltage (Vdc
Surge voltage (Vdc
)
)
2.5
2.9
6.3
7.2
10
12
Appearance
Capacitance change
No significant damage
20% of the initial value
≦±
D.F. (tan
ESR
Leakage current
)
150% of the initial specified value
150% of the initial specified value
The initial specified value
δ
≦
≦
≦
Soldering Heat
The following specifications shall be satisfied when the solder temperature is reduced back to 20 C to measure dip resistance after
°
soldering has been performed under the recommended soldering conditions.
Appearance
No significant damage
Capacitance value
Within the specified tolerance range
D.F. (tan
ESR
Leakage current
)
The initial specified value
The initial specified value
The initial specified value (Voltage treatment)
δ
≦
≦
≦
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 125℃.
DIMENSIONS [mm]
MARKING
◆
◆
●
EX) 10V330µF
Terminal Code : A
W
D
22A
330
Size code
E61
L
A
B
C
W
P
φD
5
V
10
5.8 5.3 5.3 5.9 0.5 to 0.8 1.4
F61
H70
J80
6.3 5.8 6.6 6.6 7.2 0.5 to 0.8 1.9
6.7 8.3 8.3 9.0 0.7 to 1.1 3.1
10 7.7 10.3 10.3 11.0 0.7 to 1.1 4.5
8
0.3max.
A±0.2
L±0.3
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
CAT. No. E1001Y 2024