A
L
D
DVANCED
INEAR
EVICES, INC.
ALD2704A/ALD2704B
ALD2704
DUAL RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER
GENERAL DESCRIPTION
FEATURES
The ALD2704 is a dual monolithic operational amplifier with MOSFET
input that has rail-to-rail input and output voltage ranges. The input
voltage range and output voltage range are very close to the positive and
negative power supply voltages. Typically the input voltage can be
• Rail-to-rail input and output voltage ranges
• Symmetrical push-pull output drives
• Output settles to 2mV of supply rails
• 5.0V/µs slew rate
• Highcapacitiveloadcapability--upto4000pF
• No frequency compensation required -- unity
gain stable
+
beyond positive power supply voltage V or the negative power supply
-
voltage V by up to 300mV. The output voltage swings to within 60mV of
either positive or negative power supply voltages at rated load.
• Extremely low input bias currents -- <1.0pA
typical (20pA max.)
• Ideal for high source impedance applications
• High voltage gain -- typically 100V/mV
• Output short circuit protected
With high impedance load, the output voltage of the ALD2704 ap-
proaches within 1mV of the power supply rails. This device is designed
as an alternative to the popular J-FET input operational amplifier in
applicationswhereloweroperatingvoltages,suchas9Vbatteryor±3.25V
to ±6Vpowersuppliesarebeingused. TheALD2704offershighslewrate
of 5V/µs. It is designed and manufactured with Advanced Linear Devices'
standardenhancedACMOSsilicongateCMOSprocess, and it offerslow
unit cost and exceptional reliability.
• Unity gain bandwidth of 2.1MHz
APPLICATIONS
• Voltage amplifier
• Voltage follower/buffer
• Charge integrator
The rail-to-rail input and output feature of the ALD2704 expands signal
voltage range for a given operating supply voltage and allows numerous
analog serial stages to be implemented without losing operating voltage
margin. The output stage is designed to drive up to 10mA into 400pF
capacitive and 1.5KΩ resistive loads at unity gain and up to 4000pF at a
gain of 5. Short circuit protection to either ground or the power supply rails
is at approximately 15mA clamp current. Due to complementary output
stage design, the output can source and sink 10mA into a load with
symmetrical drive and is ideally suited for applications where push-pull
voltage drive is desired.
• Photodiode amplifier
• Data acquisition systems
• High performance portable instruments
• Signal conditioning circuits
• Low leakage amplifiers
• Active filters
• Sample/Hold amplifier
• Picoammeter
• Current to voltage converter
• Coaxial cable driver
• Capacitive sensor amplifier
• Piezoelectric transducer amplifier
For each of the operational amplifier, the offset voltage is trimmed on-chip
to eliminate the need for external nulling in many applications. For
precision applications, the output is designed to settle to 0.1% in 2µs. In
large signal buffer applications, the operational amplifier can function as
an ultrahigh input impedance voltage follower /buffer that allows input and
output voltage swings from positive to negative supply voltages. This
featureisintendedtogreatlysimplifysystemsdesignandeliminatehigher
voltage power supplies in many applications.
PIN CONFIGURATION
ORDERING INFORMATION
Operating Temperature Range*
+
OUT
1
8
V
A
A
-55°C to +125°C
0°C to +70°C
0°C to +70°C
-IN
2
3
7
6
OUT
-IN
B
8-Pin
8-Pin
8-Pin
CERDIP
Package
Small Outline
Package (SOIC)
Plastic Dip
Package
+IN
A
-
B
V
4
5
+IN
B
ALD2704A DA
ALD2704B DA
ALD2704 DA
ALD2704A SA
ALD2704B SA
ALD2704 SA
ALD2704A PA
ALD2704B PA
ALD2704 PA
TOP VIEW
DA, PA, SA PACKAGE
* Contact factory for industrial temperature range
© 1998 Advanced Linear Devices, Inc. 415Tasman Drive, Sunnyvale, California 94089 -1706 Tel: (408) 747-1155 Fax: (408) 747-1286 http://www.aldinc.com
5秒后页面跳转
解析光耦仿真器：升级光耦合器技术的必要性
英伟达新一代Blackwell GPU过热问题致交付延迟
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
