A
L
D
DVANCED
INEAR
EVICES, INC.
ALD2704A/ALD2704B
ALD2704
DUAL RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER
GENERAL DESCRIPTION
FEATURES
The ALD2704 is a dual monolithic operational amplifier with MOSFET
input that has rail-to-rail input and output voltage ranges. The input
voltage range and output voltage range are very close to the positive and
negative power supply voltages. Typically the input voltage can be
• Rail-to-rail input and output voltage ranges
• Symmetrical push-pull output drives
• Output settles to 2mV of supply rails
• 5.0V/µs slew rate
• Highcapacitiveloadcapability--upto4000pF
• No frequency compensation required -- unity
gain stable
+
beyond positive power supply voltage V or the negative power supply
-
voltage V by up to 300mV. The output voltage swings to within 60mV of
either positive or negative power supply voltages at rated load.
• Extremely low input bias currents -- <1.0pA
typical (20pA max.)
• Ideal for high source impedance applications
• High voltage gain -- typically 100V/mV
• Output short circuit protected
With high impedance load, the output voltage of the ALD2704 ap-
proaches within 1mV of the power supply rails. This device is designed
as an alternative to the popular J-FET input operational amplifier in
applicationswhereloweroperatingvoltages,suchas9Vbatteryor±3.25V
to ±6Vpowersuppliesarebeingused. TheALD2704offershighslewrate
of 5V/µs. It is designed and manufactured with Advanced Linear Devices'
standardenhancedACMOSsilicongateCMOSprocess, and it offerslow
unit cost and exceptional reliability.
• Unity gain bandwidth of 2.1MHz
APPLICATIONS
• Voltage amplifier
• Voltage follower/buffer
• Charge integrator
The rail-to-rail input and output feature of the ALD2704 expands signal
voltage range for a given operating supply voltage and allows numerous
analog serial stages to be implemented without losing operating voltage
margin. The output stage is designed to drive up to 10mA into 400pF
capacitive and 1.5KΩ resistive loads at unity gain and up to 4000pF at a
gain of 5. Short circuit protection to either ground or the power supply rails
is at approximately 15mA clamp current. Due to complementary output
stage design, the output can source and sink 10mA into a load with
symmetrical drive and is ideally suited for applications where push-pull
voltage drive is desired.
• Photodiode amplifier
• Data acquisition systems
• High performance portable instruments
• Signal conditioning circuits
• Low leakage amplifiers
• Active filters
• Sample/Hold amplifier
• Picoammeter
• Current to voltage converter
• Coaxial cable driver
• Capacitive sensor amplifier
• Piezoelectric transducer amplifier
For each of the operational amplifier, the offset voltage is trimmed on-chip
to eliminate the need for external nulling in many applications. For
precision applications, the output is designed to settle to 0.1% in 2µs. In
large signal buffer applications, the operational amplifier can function as
an ultrahigh input impedance voltage follower /buffer that allows input and
output voltage swings from positive to negative supply voltages. This
featureisintendedtogreatlysimplifysystemsdesignandeliminatehigher
voltage power supplies in many applications.
PIN CONFIGURATION
ORDERING INFORMATION
Operating Temperature Range*
+
OUT
1
8
V
A
A
-55°C to +125°C
0°C to +70°C
0°C to +70°C
-IN
2
3
7
6
OUT
-IN
B
8-Pin
8-Pin
8-Pin
CERDIP
Package
Small Outline
Package (SOIC)
Plastic Dip
Package
+IN
A
-
B
V
4
5
+IN
B
ALD2704A DA
ALD2704B DA
ALD2704 DA
ALD2704A SA
ALD2704B SA
ALD2704 SA
ALD2704A PA
ALD2704B PA
ALD2704 PA
TOP VIEW
DA, PA, SA PACKAGE
* Contact factory for industrial temperature range
© 1998 Advanced Linear Devices, Inc. 415Tasman Drive, Sunnyvale, California 94089 -1706 Tel: (408) 747-1155 Fax: (408) 747-1286 http://www.aldinc.com
5秒后页面跳转
英伟达新AI芯片Rubin或提前半年亮相
苹果iPhone 17将全系采用三星/LG显示LTPO OLED面板
三星深化印度制造布局，供应链本地化进程加速
芯擎科技“星辰一号”自动驾驶芯片点亮成功，2025年量产在即
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
