Dual-Channel, 2.5 kV Isolators with
Integrated DC-to-DC Converter
Data Sheet
ADuM5200/ADuM5201/ADuM5202
FEATURES
FUNCTIONAL BLOCK DIAGRAMS
isoPower integrated, isolated dc-to-dc converter
Regulated 3.3 V or 5 V output
Up to 500 mW output power
Dual, dc-to-25 Mbps (NRZ) signal isolation channels
16-lead SOIC package with 7.6 mm creepage
High temperature operation: 105°C maximum
High common-mode transient immunity: >25 kV/μs
Safety and regulatory approvals
OSC
RECT
REG
1
2
3
4
5
6
7
8
16
15
14
13
V
V
ISO
DD1
GND
GND
ISO
1
V
/V
IA OA
V /V
IA OA
2-CHANNEL iCOUPLER CORE
V
/V
IB OB
V /V
IB OB
RC
12 NC
IN
RC
11
10
9
V
V
SEL
SEL
ADuM5200/
ADuM5201/
ADuM5202
UL recognition
V
/NC
/NC
E1
GND
E2
2500 V rms for 1 minute per UL 1577
CSA Component Acceptance Notice #5A)
VDE certificate of conformity (pending)
IEC 60747-5-2 (VDE 0884, Part 2):2003-01
GND
ISO
1
Figure 1.
V
IORM = 560 VPEAK
V
V
V
V
IA
IB
OA
OB
3
4
14
13
APPLICATIONS
ADuM5200
RS-232/RS-422/RS-485 transceivers
Industrial field bus isolation
Power supply start-up bias and gate drives
Isolated sensor interfaces
Figure 2. ADuM5200
Industrial PLCs
V
V
V
IA
OA
IB
3
4
14
13
GENERAL DESCRIPTION
ADuM5201
V
OB
The ADuM5200/ADuM5201/ADuM52021 are dual-channel digital
isolators with isoPower®, an integrated, isolated dc-to-dc converter.
Based on the Analog Devices, Inc., iCoupler® technology, the
dc-to-dc converter provides up to 500 mW of regulated, isolated
power at either 5.0 V or 3.3 V from a 5.0 V input supply, or 3.3 V
from a 3.3 V supply at the power levels shown in Table 1. These
devices eliminate the need for a separate, isolated dc-to-dc converter
in low power isolated designs. The iCoupler chip scale transformer
technology is used to isolate the logic signals and for the magnetic
components of the dc-to-dc converter. The result is a small form
factor, total isolation solution.
Figure 3. ADuM5201
V
V
V
V
OA
IA
IB
3
4
14
13
ADuM5202
OB
Figure 4. ADuM5202
Table 1. Power Levels
Input Voltage (V) Output Voltage (V) Output Power (mW)
The ADuM5200/ADuM5201/ADuM5202 isolators provide two
independent isolation channels in a variety of channel configurations
and data rates (see the Ordering Guide for more information).
5.0
5.0
3.3
5.0
3.3
3.3
500
330
200
isoPower uses high frequency switching elements to transfer power
through its transformer. Special care must be taken during printed
circuit board (PCB) layout to meet emissions standards. See the
AN-0971 Application Note for board layout recommendations.
1
Protected by U.S. Patents 5,952,849; 6,873,065; 6,903,578; and 7,075,329.
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 www.analog.com
Fax: 781.461.3113 ©2009-2012 Analog Devices, Inc. All rights reserved.