ADS58C28
www.ti.com
SBAS509B –JUNE 2010–REVISED OCTOBER 2010
Dual Channel IF Receiver with SNRBoost3G
Check for Samples: ADS58C28
1
FEATURES
DESCRIPTION
23
•
Maximum Sample Rate: 200MSPS
The ADS58C28 is
a
dual-channel, 11-bit
analog-to-digital converter (ADC) with sampling rates
up to 200MSPS. The device uses innovative design
techniques to achieve high dynamic performance,
while consuming extremely low power at 1.8V supply.
This architecture makes it well-suited for multi-carrier,
wide bandwidth communications applications.
The ADS58C28 uses third-generation SNRBoost3G
technology to overcome SNR limitation as a result of
quantization noise (for bandwidths less than Nyquist,
fS/2). Enhancements in the SNRBoost3G technology
allow support for SNR improvements over wide
bandwidths (up to 60MHz). In addition, separate
SNRBoost3G coefficients can also be programmed for
each channel.
•
High Dynamic Performance:
–
–
83dBc SFDR at 140MHz
72.5dBFS SNR with 60MHz BW Using
SNRBoost3G Technology
•
•
SNRBoost3G Highlights:
–
–
Supports Wide Bandwidth (up to 60MHz)
Programmable Bandwidths:
20MHz, 30MHz, and 40MHz
–
–
Flat Noise Floor within the Band
Independent SNRBoost3G Coefficients for
Both Channels
Output Interface:
The device has a digital gain function that can be
used to improve SFDR performance at lower
–
Double Data Rate (DDR) LVDS with
Programmable Swing and Strength:
full-scale input ranges. It includes
a dc offset
–
–
–
–
Standard Swing: 350mV
correction loop that can be used to cancel the ADC
offset. The digital outputs of all channels are output
as double data rate (DDR) low-voltage differential
signaling (LVDS) together with an LVDS clock output.
The low data rate of this interface (400MBPS at
200MSPS sample rate) makes it possible to use
Low Swing: 200mV
Default Strength: 100Ω termination
2x Strength: 50Ω termination
–
–
Compatible with GC6016
1.8V Parallel CMOS Interface Also
Supported
low-cost
field-programmable
gate
array
(FPGA)-based receivers. The strength of the LVDS
output buffers can be increased to support 50Ω
differential termination. This increase allows the
output clock signal to be connected to two separate
receiver chips with an effective 50Ω termination (such
as the two clock ports of the GC5330). The same
digital output pins can also be configured as a parallel
1.8V CMOS interface.
•
•
Ultralow Power with Single 1.8V Supply:
–
–
470mW Total Power
710mW Total Power (200MSPS) with
SNRBoost3G on Both Channels
Programmable Gain up to 6dB for
SNR/SFDR Trade-off
The device includes internal references while the
traditional reference pins and associated decoupling
capacitors have been eliminated. The ADS58C28 is
specified over the industrial temperature range
(–40°C to +85°C).
•
•
•
DC Offset Correction
Supports Low Input Clock Amplitude
Package: QFN-64 (9mm × 9mm)
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
3
PowerPAD is a trademark of Texas Instruments Incorporated.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2010, Texas Instruments Incorporated