50 mA/500 mA, High Efficiency,
Ultralow Power Step-Down Regulator
Data Sheet
ADP5301
TYPICAL APPLICATION CIRCUIT
FEATURES
Input start-up voltage range: 2.15 V to 6.50 V
Operates down to 2.00 V voltage
Ultralow 180 nA quiescent current with no load
Selectable output voltage of 1.2 V to 3.6 V or 0.8 V to 5.0 V
1.5% output accuracy over full temperature range in
PWM mode
2.2µH
V
= 3.6V
10µF
V
OUT
IN
PVIN
EN
SW
ADP5301
10µF
(9-BALL WLCSP)
ON
PGND
OFF
HYS
PWM
SYNC/
MODE
Selectable hysteresis mode or PWM operation mode
Output current
FB
VID0: 1.2V VID8: 2.5V
VID1: 1.5V VID9: 2.6V
VID2: 1.8V VID10: 2.7V
VID3: 2.0V VID11: 2.8V
VID4: 2.1V VID12: 2.9V
VID5: 2.2V VID13: 3.0V
VID6: 2.3V VID14: 3.3V
VID7: 2.4V VID15: 3.6V
Up to 50 mA in hysteresis mode
Up to 500 mA in PWM mode
VOUTOK flag monitors the output voltage
100% duty cycle operation mode
2 MHz switching frequency with optional synchronization
input from 1.5 MHz to 2.5 MHz
VOUTOK
VID
R
VID
AGND
Figure 1.
QOD option
UVLO, OCP, and TSD protection
9-ball, 1.65 mm × 1.87 mm WLCSP
−40°C to +125°C junction temperature
APPLICATIONS
Energy (gas and water) metering
Portable and battery-powered equipment
Medical applications
Keep-alive power supplies
GENERAL DESCRIPTION
The ADP5301 is a high efficiency, ultralow quiescent current
step-down regulator that draws only a 180nA quiescent current
to regulate the output at no load.
The ADP5301 contains a VOUTOK flag, which monitors the
output voltageand runs at a 2MHzswitching frequency in
PWM mode. SYNC/MODE can synchronize to an external
clock from 1.5MHzto 2.5 MHz.
The ADP5301 runs from an input startup voltage range of 2.15V
to 6.50 V, allowing the use ofmultiplealkaline/NiMH, Li-Ion
cells, or other power sources. The output voltage is selectable from
0.8 V to 5.0 V by an externalVID resistor and factory fuse. The
totalsolution requires only fourtiny external components.
Other key features in the ADP5301 include separateenabling,
quick output discharge(QOD), and safety featuressuch as
overcurrent protection (OCP), thermalshutdown(TSD), and
input undervoltagelockout (UVLO).
The ADP5301 can operatebetweenhysteresis mode and PWM
mode via the SYNC/MODE pin. The regulator in hysteresis mode
achieves excellent efficiency at a power of less than 1mW and
provides up to 50 mA of output current. The regulator in PWM
mode produces a lower output ripple andsuppliesup to 500 mA
of output current. The flexible configuration capability during
operation of the device enables very efficient power management
to meet both the longest battery life and low systemnoise
requirements.
The ADP5301 is available in a 9-ball, 1.65 mm × 1.87 mm
WLCSP rated for a −40°C to +125°C junctiontemperature range.
Rev. B
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility isassumed by Analog Devicesfor its use,norfor any infringements of patents or other
rights of third pa rties thatmay resultf rom its use.S pec if icatio ns s ubje ct to cha nge w ithoutnotice .No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices .
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2015–2016 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com