5秒后页面跳转
ADM485ARZ PDF预览

ADM485ARZ

更新时间: 2024-01-29 08:28:28
品牌 Logo 应用领域
亚德诺 - ADI 线路驱动器或接收器驱动程序和接口接口集成电路光电二极管信息通信管理PC
页数 文件大小 规格书
16页 607K
描述
Meets EIA RS-485 standard

ADM485ARZ 技术参数

是否无铅:含铅是否Rohs认证:符合
生命周期:Active零件包装代码:SOIC
包装说明:SOIC-8针数:8
Reach Compliance Code:compliantECCN代码:EAR99
HTS代码:8542.39.00.01风险等级:0.71
Samacsys Confidence:3Samacsys Status:Released
Samacsys PartID:3592Samacsys Pin Count:8
Samacsys Part Category:Integrated CircuitSamacsys Package Category:Small Outline Packages
Samacsys Footprint Name:R-8 (SOIC)Samacsys Released Date:2015-04-16 09:48:08
Is Samacsys:N其他特性:1 RECEIVER ACTIVE UNDER SHUTDOWN; COMMON I/O; TRISTATABLE RECEIVERS
差分输出:YES驱动器位数:1
高电平输入电流最大值:0.000001 A输入特性:DIFFERENTIAL SCHMITT TRIGGER
接口集成电路类型:LINE TRANSCEIVER接口标准:EIA-422; EIA-485
JESD-30 代码:R-PDSO-G8JESD-609代码:e3
长度:4.9 mm湿度敏感等级:1
功能数量:1端子数量:8
最高工作温度:70 °C最低工作温度:
最小输出摆幅:1.5 V最大输出低电流:0.004 A
封装主体材料:PLASTIC/EPOXY封装代码:SOP
封装等效代码:SOP8,.25封装形状:RECTANGULAR
封装形式:SMALL OUTLINE峰值回流温度(摄氏度):260
电源:5 V认证状态:Not Qualified
最大接收延迟:30 ns接收器位数:1
座面最大高度:1.75 mm子类别:Line Driver or Receivers
最大压摆率:2.2 mA最大供电电压:5.25 V
最小供电电压:4.75 V标称供电电压:5 V
表面贴装:YES技术:BICMOS
温度等级:COMMERCIAL端子面层:Matte Tin (Sn)
端子形式:GULL WING端子节距:1.27 mm
端子位置:DUAL处于峰值回流温度下的最长时间:30
最大传输延迟:15 ns宽度:3.9 mm
Base Number Matches:1

ADM485ARZ 数据手册

 浏览型号ADM485ARZ的Datasheet PDF文件第2页浏览型号ADM485ARZ的Datasheet PDF文件第3页浏览型号ADM485ARZ的Datasheet PDF文件第4页浏览型号ADM485ARZ的Datasheet PDF文件第5页浏览型号ADM485ARZ的Datasheet PDF文件第6页浏览型号ADM485ARZ的Datasheet PDF文件第7页 
5 V Low Power  
EIA RS-485 Transceiver  
ADM485  
FEATURES  
FUNCTIONAL BLOCK DIAGRAM  
Meets EIA RS-485 standard  
5 Mbps data rate  
ADM485  
1
8
Single 5 V supply  
RO  
RE  
V
CC  
R
–7 V to +12 V bus common-mode range  
High speed, low power BiCMOS  
Thermal shutdown protection  
Short-circuit protection  
Driver propagation delay: 10 ns typical  
Receiver propagation delay: 15 ns typical  
High-Z outputs with power off  
Superior upgrade for LTC485  
2
3
4
7
6
5
B
DE  
DI  
A
GND  
D
Figure 1.  
APPLICATIONS  
Low power RS-485 systems  
DTE/DCE interface  
Packet switching  
Local area networks (LNAs)  
Data concentration  
Data multiplexers  
Integrated services digital network (ISDN)  
GENERAL DESCRIPTION  
The ADM485 is a differential line transceiver suitable for high  
speed bidirectional data communication on multipoint bus  
transmission lines. It is designed for balanced data transmission  
and complies with EIA standards RS-485 and RS-422. The part  
contains a differential line driver and a differential line receiver.  
Both the driver and the receiver can be enabled independently.  
When disabled, the outputs are three-stated.  
The receiver contains a fail-safe feature that results in a logic  
high output state if the inputs are unconnected (floating).  
The ADM485 is fabricated on BiCMOS, an advanced mixed  
technology process combining low power CMOS with fast  
switching bipolar technology. All inputs and outputs contain  
protection against ESD; all driver outputs feature high source  
and sink current capability. An epitaxial layer is used to guard  
against latch-up.  
The ADM485 operates from a single 5 V power supply.  
Excessive power dissipation caused by bus contention or by  
output shorting is prevented by a thermal shutdown circuit. If  
during fault conditions, a significant temperature increase is  
detected in the internal driver circuitry, this feature forces the  
driver output into a high impedance state.  
The ADM485 features extremely fast switching speeds. Minimal  
driver propagation delays permit transmission at data rates up  
to 5 Mbps while low skew minimizes EMI interference.  
The part is fully specified over the commercial and industrial  
temperature range and is available in 8-lead PDIP, 8-lead SOIC,  
and small footprint, 8-lead MSOP packages.  
Up to 32 transceivers can be connected simultaneously on a  
bus, but only one driver should be enabled at any time. It is  
important, therefore, that the remaining disabled drivers do not  
load the bus. To ensure this, the ADM485 driver features high  
output impedance when disabled and when powered down,  
which minimizes the loading effect when the transceiver is not  
being used. The high impedance driver output is maintained  
over the common-mode voltage range of −7 V to +12 V.  
Rev. F  
Information furnished by Analog Devices is believed to be accurate and reliable. However, no  
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other  
rights of third parties that may result from its use. Specifications subject to change without notice. No  
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.  
Trademarks and registeredtrademarks arethe property of their respective owners.  
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.  
Tel: 781.329.4700  
www.analog.com  
Fax: 781.461.3113 ©1993–2008 Analog Devices, Inc. All rights reserved.  
 

ADM485ARZ 替代型号

型号 品牌 替代类型 描述 数据表
ADM485ARMZ-REEL7 ADI

完全替代

5 V, Low Power, 5 Mbps, Half Duplex EIA RS-485 Transceiver
ADM485ARMZ ADI

完全替代

5 V, Low Power, 5 Mbps, Half Duplex EIA RS-485 Transceiver
ADM485ARZ-REEL ADI

完全替代

5 V, Low Power, 5 Mbps, Half Duplex EIA RS-485 Transceiver

与ADM485ARZ相关器件

型号 品牌 获取价格 描述 数据表
ADM485ARZ1 ADI

获取价格

Meets EIA RS-485 standard
ADM485ARZ-REEL ADI

获取价格

5 V, Low Power, 5 Mbps, Half Duplex EIA RS-485 Transceiver
ADM485ARZ-REEL1 ADI

获取价格

Meets EIA RS-485 standard
ADM485E ADI

获取价格

5 V, 【15 kV ESD Protected Half-Duplex, RS-485
ADM485E_15 ADI

获取价格

Half-Duplex, RS-485/RS-422 Transceivers
ADM485EARZ ADI

获取价格

5 V, 【15 kV ESD Protected Half-Duplex, RS-485
ADM485EARZ-REEL7 ADI

获取价格

5 V, 【15 kV ESD Protected Half-Duplex, RS-485
ADM485JN ADI

获取价格

+5 V Low Power EIA RS-485 Transceiver
ADM485JN ROCHESTER

获取价格

LINE TRANSCEIVER, PDIP8, MO-095AA, PLASTIC, DIP-8
ADM485JNZ ADI

获取价格

5 V, Low Power, 5 Mbps, Half Duplex EIA RS-485 Transceiver