Datasheet > ADM485ARMZ-REEL7

ADM485ARMZ-REEL7

更新时间： 2024-01-06 18:14:42

品牌	Logo	应用领域
亚德诺 - ADI		驱动信息通信管理光电二极管接口集成电路驱动器
页数	文件大小	规格书
17页	549K
描述
5 V, Low Power, 5 Mbps, Half Duplex EIA RS-485 Transceiver

阅读下载

中文翻译

获取价格

技术参数
数据手册
替代型号

如果您发现信息不准确，欢迎纠错

ADM485ARMZ-REEL7 技术参数

是否无铅：	含铅	是否Rohs认证：	符合
生命周期：	Active	零件包装代码：	TSSOP
包装说明：	MSOP-8	针数：	8
Reach Compliance Code：	compliant	ECCN代码：	EAR99
HTS代码：	8542.39.00.01	风险等级：	1.15
Is Samacsys：	N	其他特性：	1 RECEIVER ACTIVE UNDER SHUTDOWN; COMMON I/O; TRISTATABLE RECEIVERS
差分输出：	YES	驱动器位数：	1
输入特性：	DIFFERENTIAL SCHMITT TRIGGER	接口集成电路类型：	LINE TRANSCEIVER
接口标准：	EIA-422; EIA-485	JESD-30 代码：	S-PDSO-G8
JESD-609代码：	e3	长度：	3 mm
湿度敏感等级：	1	功能数量：	1
端子数量：	8	最高工作温度：	85 °C
最低工作温度：	-40 °C	最小输出摆幅：	1.5 V
最大输出低电流：	0.004 A	封装主体材料：	PLASTIC/EPOXY
封装代码：	TSSOP	封装等效代码：	TSSOP8,.19
封装形状：	SQUARE	封装形式：	SMALL OUTLINE, THIN PROFILE, SHRINK PITCH
峰值回流温度（摄氏度）：	260	电源：	5 V
认证状态：	Not Qualified	最大接收延迟：	30 ns
接收器位数：	1	座面最大高度：	1.1 mm
子类别：	Line Driver or Receivers	最大压摆率：	2.2 mA
最大供电电压：	5.25 V	最小供电电压：	4.75 V
标称供电电压：	5 V	表面贴装：	YES
技术：	BICMOS	温度等级：	INDUSTRIAL
端子面层：	Matte Tin (Sn)	端子形式：	GULL WING
端子节距：	0.65 mm	端子位置：	DUAL
处于峰值回流温度下的最长时间：	30	最大传输延迟：	15 ns
宽度：	3 mm	Base Number Matches：	1

ADM485ARMZ-REEL7 数据手册

5 V Low Power

EIA RS-485 Transceiver

ADM485

FEATURES

FUNCTIONAL BLOCK DIAGRAM

Meets EIA RS-485 standard

5 Mbps data rate

ADM485

Single 5 V supply

–7 V to +12 V bus common-mode range

High speed, low power BiCMOS

Thermal shutdown protection

Short-circuit protection

Driver propagation delay: 10 ns typical

Receiver propagation delay: 15 ns typical

High-Z outputs with power off

Superior upgrade for LTC485

GND

Figure 1.

APPLICATIONS

Low power RS-485 systems

DTE/DCE interface

Packet switching

Local area networks (LNAs)

Data concentration

Data multiplexers

Integrated services digital network (ISDN)

GENERAL DESCRIPTION

The ADM485 is a differential line transceiver suitable for high

speed bidirectional data communication on multipoint bus

transmission lines. It is designed for balanced data transmission

and complies with EIA standards RS-485 and RS-422. The part

contains a differential line driver and a differential line receiver.

Both the driver and the receiver can be enabled independently.

When disabled, the outputs are three-stated.

The receiver contains a fail-safe feature that results in a logic

high output state if the inputs are unconnected (floating).

The ADM485 is fabricated on BiCMOS, an advanced mixed

technology process combining low power CMOS with fast

switching bipolar technology. All inputs and outputs contain

protection against ESD; all driver outputs feature high source

and sink current capability. An epitaxial layer is used to guard

against latch-up.

The ADM485 operates from a single 5 V power supply.

Excessive power dissipation caused by bus contention or by

output shorting is prevented by a thermal shutdown circuit. If

during fault conditions, a significant temperature increase is

detected in the internal driver circuitry, this feature forces the

driver output into a high impedance state.

The ADM485 features extremely fast switching speeds. Minimal

driver propagation delays permit transmission at data rates up

to 5 Mbps while low skew minimizes EMI interference.

The part is fully specified over the commercial and industrial

temperature range and is available in 8-lead PDIP, 8-lead SOIC,

and small footprint, 8-lead MSOP packages.

Up to 32 transceivers can be connected simultaneously on a

bus, but only one driver should be enabled at any time. It is

important, therefore, that the remaining disabled drivers do not

load the bus. To ensure this, the ADM485 driver features high

output impedance when disabled and when powered down,

which minimizes the loading effect when the transceiver is not

being used. The high impedance driver output is maintained

over the common-mode voltage range of −7 V to +12 V.

Rev. F

Information furnished by Analog Devices is believed to be accurate and reliable. However, no

responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other

rights of third parties that may result from its use. Specifications subject to change without notice. No

license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

Trademarks and registeredtrademarks arethe property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Tel: 781.329.4700

www.analog.com

12 3 4 5 6 7...17

中文翻译

下载PDF

ADM485ARMZ-REEL7 替代型号

型号	品牌	替代类型	描述	数据表
ADM485ARZ-REEL	ADI	完全替代	5 V, Low Power, 5 Mbps, Half Duplex EIA RS-485 Transceiver
ADM1485ARZ	ADI	完全替代	5 V Low Power EIA RS-485 Transceiver
ADM485ARZ	ADI	完全替代	Meets EIA RS-485 standard

与ADM485ARMZ-REEL7相关器件

型号	品牌	获取价格	描述	数据表
ADM485ARMZ-REEL71	ADI	获取价格	Meets EIA RS-485 standard
ADM485AR-REEL	ADI	获取价格	Meets EIA RS-485 standard
ADM485AR-REEL	ROCHESTER	获取价格	LINE TRANSCEIVER, PDSO8, MS-012AA, SOIC-8
ADM485ARZ	ROCHESTER	获取价格	LINE TRANSCEIVER, PDSO8, LEAD FREE, MS-012AA, SOIC-8
ADM485ARZ	ADI	获取价格	Meets EIA RS-485 standard
ADM485ARZ	UMW	获取价格	RS-485 / RS-422芯片
ADM485ARZ1	ADI	获取价格	Meets EIA RS-485 standard
ADM485ARZ-REEL	ADI	获取价格	5 V, Low Power, 5 Mbps, Half Duplex EIA RS-485 Transceiver
ADM485ARZ-REEL1	ADI	获取价格	Meets EIA RS-485 standard
ADM485E	ADI	获取价格	5 V, 【15 kV ESD Protected Half-Duplex, RS-485

与ADM485ARMZ-REEL7相关文章

BSS138LT3G：一款高效能N沟道MOSFET的全面解析
2024-07-04

4
解读EGP10B二极管资料手册：产品特性、参数分析
2024-07-04

3
RT9164AGG手册资料详解：引脚信息、设计指南
2024-07-04

3
2SA1037KPT资料详解：产品特性、电气参数、设计指南
2024-07-04

5

产品中心

服务支持

精选活动

关于我们

帮助中心

ADM485ARMZ-REEL7

ADM485ARMZ-REEL7 技术参数

ADM485ARMZ-REEL7 数据手册

ADM485ARMZ-REEL7 替代型号

与ADM485ARMZ-REEL7相关器件

与ADM485ARMZ-REEL7相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

ADM485ARMZ-REEL7

ADM485ARMZ-REEL7 技术参数

ADM485ARMZ-REEL7 数据手册

ADM485ARMZ-REEL7 替代型号

与ADM485ARMZ-REEL7相关器件

与ADM485ARMZ-REEL7相关文章

您还可以找

您在本页遇到什么问题？