Single-Phase Multifunction Metering IC
with di/dt Sensor Interface
ADE7753
line-voltage period measurement, and rms calculation on the
voltage and current. The selectable on-chip digital integrator
provides direct interface to di/dt current sensors such as
FEATURES
High accuracy; supports IEC 60687/61036/61268 and
IEC 62053-21/62053-22/62053-23
Rogowski coils, eliminating the need for an external analog
integrator and resulting in excellent long-term stability and pre-
cise phase matching between the current and voltage channels.
On-chip digital integrator enables direct interface to current
sensors with di/dt output
A PGA in the current channel allows direct interface to
shunts and current transformers
The ADE7753 provides a serial interface to read data, and a
pulse output frequency (CF), which is proportional to the active
power. Various system calibration features, i.e., channel offset
correction, phase calibration, and power calibration, ensure
high accuracy. The part also detects short duration low or high
voltage variations.
Active, reactive, and apparent energy; sampled waveform;
current and voltage rms
Less than 0.1% error in active energy measurement over a
dynamic range of 1000 to 1 at 25°C
Positive-only energy accumulation mode available
On-chip user programmable threshold for line voltage surge
and SAG and PSU supervisory
The positive-only accumulation mode gives the option to
accumulate energy only when positive power is detected. An
internal no-load threshold ensures that the part does not exhibit
any creep when there is no load. The zero-crossing output (ZX)
produces a pulse that is synchronized to the zero-crossing point
of the line voltage. This signal is used internally in the line cycle
active and apparent energy accumulation modes, which enables
faster calibration.
Digital calibration for power, phase, and input offset
On-chip temperature sensor ( 3°C typical)
SPI® compatible serial interface
Pulse output with programmable frequency
IRQ
Interrupt request pin (
) and status register
Reference 2.4 V with external overdrive capability
Single 5 V supply, low power (25 mW typical)
GENERAL DESCRIPTION
The ADE77531 features proprietary ADCs and DSP for high
accuracy over large variations in environmental conditions and
time. The ADE7753 incorporates two second-order 16-bit -Δ
ADCs, a digital integrator (on CH1), reference circuitry,
temperature sensor, and all the signal processing required to
perform active, reactive, and apparent energy measurements,
The interrupt status register indicates the nature of the interrupt,
and the interrupt enable register controls which event produces
IRQ
an output on the
pin, an open-drain, active low logic output.
The ADE7753 is available in a 20-lead SSOP package.
FUNCTIONAL BLOCK DIAGRAM
AVDD
DVDD
DGND
RESET
INTEGRATOR
WGAIN[11:0]
PGA
ADE7753
MULTIPLIER LPF2
V1P
V1N
dt
ADC
HPF1
PHCAL[5:0]
CFNUM[11:0]
TEMP
SENSOR
APOS[15:0]
2
DFC
CF
IRMSOS[11:0]
VRMSOS[11:0]
CFDEN[11:0]
VAGAIN[11:0]
2
x
PGA
V2P
V2N
|x|
ADC
VADIV[7:0]
%
%
WDIV[7:0]
LPF1
ZX
SAG
4k
REGISTERS AND
SERIAL INTERFACE
2.4V
REFERENCE
02875-A-001
AGND
REF
CLKIN CLKOUT
DIN DOUT SCLK
CS IRQ
IN/OUT
Figure 1.
1U.S. Patents 5,745,323; 5,760,617; 5,862,069; 5,872,469.
Rev. C
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 www.analog.com
Fax: 781.461.3113 ©2003–2010 Analog Devices, Inc. All rights reserved.